[PDF] Toshiba Personal Computer Satellite A100/A105 TECRA A7 (PSAA8/PSAA9) (PTA70/PTA71) (PSAAx) Maintenance Manual - Free Download PDF (2024)

1 Toshiba Personal Computer Satellite A100/A105 TECRA A7 (PSAA8/PSAA9) (PTA70/PTA71) (PSAAx) Maintenance Manual TOSHIBA ...

Toshiba Personal Computer Satellite A100/A105 TECRA A7 (PSAA8/PSAA9) (PTA70/PTA71) (PSAAx) Maintenance Manual

TOSHIBA CORPORATION

S/ No.

Satellite A100/A105 / TECRA A7 Maintenance Manual

Copyright © 2005 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba Satellite A100/A105 / TECRA A7 Maintenance Manual First edition JAN. 2006 Disclaimer The information presented in this manual has been reviewed and validated for accuracy. The included set of instructions and descriptions are accurate for the Satellite A100/A105 / TECRA A7 at the time of this manual's production. However, succeeding computers and manuals are subject to change without notice. Therefore, Toshiba assumes no liability for damages incurred directly or indirectly from errors, omissions, or discrepancies between any succeeding product and this manual. Trademarks Intel and Pentium are registered trademarks of Intel Corporation. IBM, IBM PC/XT, PC/AT, PS/2 and OS/2 are registered trademarks of IBM Corporation. MS-DOS and Windows XP home edition are registered trademarks of Microsoft Corporation. Sound Blaster and Pro are trademarks of Creative Technology Ltd. UNIX is a registered trademark of X/Open Company Ltd. NetWare are registered trademarks of Novell, Inc. All other properties are trademarks or registered trademarks of their respective holders.

ii

Satellite A100/A105 / TECRA A7 Maintenance Manual

Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite A100/A105 / TECRA A7, referred to as Satellite A100/A105 / TECRA A7 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field. SAFETY PRECAUTIONS Four types of messages are used in this manual to bring important information to your attention. Each of these messages will be italicized and identified as shown below. DANGER: “Danger” indicates the existence of a hazard that could result in death or serious bodily injury, if the safety instruction is not observed.

WARNING: “Warning” indicates the existence of a hazard that could result in bodily injury, if the safety instruction is not observed.

CAUTION: “Caution” indicates the existence of a hazard that could result in property damage, if the safety instruction is not observed.

NOTE: “Note” contains general information that relates to your safe maintenance service. Improper repair of the computer may result in safety hazards. Toshiba requires service technicians and authorized dealers or service providers to ensure the following safety precautions are adhered to strictly. ‰ Be sure to fasten screws securely with the right screwdriver. If a screw is not fully fastened, it could come loose, creating a danger of a short circuit, which could cause overheating, smoke or fire. ‰ If you replace the battery pack, RTC battery or backup battery, be sure to use only the same model battery or an equivalent battery recommended by Toshiba. Installation of the wrong battery can cause the battery to explode.

Satellite A100/A105 / TECRA A7 Maintenance Manual

iii

The manual is divided into the following parts: Chapter 1

Hardware Overview describes the Satellite A100/A105 / TECRA A7 system unit and each FRU.

Chapter 2

Troubleshooting Procedures explains how to diagnose and resolve FRU problems.

Chapter 3

Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service.

Chapter 4

Replacement Procedures describes the removal and replacement of the FRUs.

Appendices

The appendices describe the following: ‰ ‰ ‰ ‰ ‰ ‰

iv

Handling the LCD module Board layout Keyboard scan/character codes Key layout Wiring diagrams BIOS Rewrite Procedures

Satellite A100/A105 / TECRA A7 Maintenance Manual

Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations. The key top symbol as it appears on the keyboard is printed in boldface type. Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause (Break) means you must hold down Ctrl and at the same time press Pause (Break). If three keys are used, hold down the first two and at the same time press the third. User input Text that you are instructed to type in is shown in the boldface type below: DISKCOPY A: B: The display Text generated by the XXXXX that appears on its display is presented in the type face below: Format complete System transferred

Satellite A100/A105 / TECRA A7 Maintenance Manual

v

Table of Contents Chapter 1

Hardware Overview

1.1 Features ................................................................................................................................1 1.2 System Unit Components ....................................................................................................9 1.3 2.5-inch HDD.....................................................................................................................15 1.4 DVD-ROM Drive ..............................................................................................................16 1.5 CD-RW/DVD-ROM Drive ................................................................................................17 1.6 DVD Super Multi (+-R Double Layer)..............................................................................18 1.7 Power Supply .....................................................................................................................19 1.8 Batteries .............................................................................................................................20 1.1.1

Main Battery...........................................................................................20

1.1.2

Battery Charging Control .......................................................................20

1.1.3

RTC Battery ...........................................................................................21

Chapter 2

Troubleshooting

2.1

Outline.................................................................................................................... 2-1

2.2

Basic Flowchart...................................................................................................... 2-2

2.3

Power Supply ......................................................................................................... 2-6 Procedure 1 Power Icon Check........................................................................... 2-6 Procedure 2 Connection Check........................................................................... 2-8 Procedure 3 Replacement Check ........................................................................ 2-8

2.4

System Board ......................................................................................................... 2-9 Procedure 3 Replacement Check .................................................................... 2-10

2.5

2.5-inch HDD ....................................................................................................... 2-11 Procedure 1 Message Check ............................................................................. 2-11

vi

Procedure 2

Partition Check ...................................................................... 2-11

Procedure 3

Format Check.......................................................................... 2-12

Procedure 4

Test Program Check ............................................................... 2-13

Procedure 5

Connector Check and Replacement Check............................. 2-14

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.6

Keyboard .............................................................................................................. 2-15 Procedure 1 Test Program Check ...................................................................... 2-15 Procedure 2 Connector Check and Replacement Check.................................... 2-15

2.7

2.8

2.9

2.10

2.11

2.12

2.13

2.14

Display ................................................................................................................. 2-16 Procedure 1

External Monitor Check ......................................................... 2-16

Procedure 2

Test Program Check ............................................................... 2-16

Procedure 3

Connector Check and Replacement Check............................. 2-16

ODD (Optical Disk Drive) ................................................................................... 2-18 Procedure 1

ODD Cleaning Check ............................................................. 2-18

Procedure 2

Test Program Check ............................................................... 2-18

Procedure 3

Connector Check and Replacement Check............................. 2-18

LAN...................................................................................................................... 2-20 Procedure 1

Test Program Check ............................................................... 2-20

Procedure 2

Connector Check and Replacement Check............................. 2-20

SD/MS/MS pro/MMC/XD Card(Optional) ......................................................... 2-21 Procedure 1

Test Program Check ............................................................... 2-21

Procedure 2

Connector Check .................................................................... 2-21

Finger Print(Optional) .......................................................................................... 2-22 Procedure 1

Test Program Check ............................................................... 2-22

Procedure 2

Connector Check .................................................................... 2-22

3D Sensor ............................................................................................................. 2-23 Procedure 1

Test Program Check ............................................................... 2-23

Procedure 2

Replacement Check ................................................................ 2-23

Parallel Port(Optional) ......................................................................................... 2-24 Procedure 1

Test Program Check ............................................................... 2-24

Procedure 2

Connector Check .................................................................... 2-24

Audio Test ............................................................................................................ 2-25 Procedure 1 Test Program Check ...................................................................... 2-25 Procedure 2 Connector Check and Replacement Check.................................... 2-25

2.15

IEEE 1394 Test .................................................................................................... 2-26 Procedure 1

Test Program Check ............................................................... 2-26

Procedure 2

Connector Check .................................................................... 2-26

Satellite A100/A105 / TECRA A7 Maintenance Manual

vii

2.16

Cooling Module.................................................................................................... 2-27 Procedure 1

Test Program Check ............................................................... 2-27

Procedure 2

Connector Check and Replacement Check............................. 2-27

Chapter 3

Diagnostic Programs

3.1

General .......................................................................................................................1

3.2

Quick Start..................................................................................................................3

3.3

viii

3.2.1

Quick Test ................................................................................................3

3.2.2

Customization Test...................................................................................3

3.2.3

Keyboard Layout test ...............................................................................7

3.2.4

Hotkey Test ..............................................................................................8

3.2.5

Audio Play Test........................................................................................8

3.2.6

Audio Record Test ...................................................................................8

3.2.7

DMI Read.................................................................................................8

3.2.8

DMI Write ................................................................................................9

3.2.9

3D Sensor Test .......................................................................................10

3.2.10

FPRD Test .............................................................................................16

3.2.11

FENR Test.............................................................................................16

3.2.12

IrDA ManMaster Test ............................................................................16

3.2.13

IrDA ManSlave Test ..............................................................................17

3.2.14

System Information ................................................................................17

3.2.15

View Logs ..............................................................................................19

3.2.16

Exit to MS DOS .....................................................................................19

3.2.17

The Diagnostics Screen Explanation......................................................19

Options .....................................................................................................................23 3.3.1

Overview ................................................................................................23

3.3.2

Batch Parameters Configuration ............................................................24

3.3.3

Item’s Parameters Configuration ...........................................................26

3.3.4

Load Batch Parameters...........................................................................27

3.3.5

Save Batch Parameters ...........................................................................28

3.3.6

LOG Parameters Setting.........................................................................28

3.3.7

Specify LOG Viewer..............................................................................29

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.3.8

Display LOG File .................................................................................. 30

3.3.9

LOG Viewer .......................................................................................... 30

3.3.10

LOG File Sample................................................................................... 32

3.4

Subtests.................................................................................................................... 33

3.5

System Test ............................................................................................................. 36

3.6

Memory Test ........................................................................................................... 40

3.7

Storage..................................................................................................................... 46

3.8

Video ....................................................................................................................... 50

3.9

Communication (COMM)....................................................................................... 59

3.10

Peripheral ................................................................................................................ 61

3.11

Error Codes and description.................................................................................... 63

3.12

Quick Test Item List................................................................................................... i

Satellite A100/A105 / TECRA A7 Maintenance Manual

ix

Chapter 4 4.1

Replacement Procedures

General ................................................................................................................... 4-1 Safety Precautions................................................................................................ 4-2 Before You Begin ................................................................................................ 4-4 Disassembly Procedures ...................................................................................... 4-5 Assembly Procedures........................................................................................... 4-5 Tools and Equipment ........................................................................................... 4-6 Screw Tightening Torque .................................................................................... 4-6 Colors of Screw Shanks ....................................................................................... 4-7 Symbols of Screws on the Computer Body ......................................................... 4-7 Symbol examples ................................................................................................. 4-7 Removing the Battery Pack ................................................................................. 4-8 Installing the Battery Pack................................................................................... 4-9 Removing the PCI Expresss Card...................................................................... 4-10 Installing the PCI Expresss Card ....................................................................... 4-11 Removing the Optional PC Card ....................................................................... 4-12 Installing the Optional PC Card......................................................................... 4-13 Removing the Momery Card ............................................................................. 4-14 Installing the Momery Card ............................................................................... 4-15 Removing the Optional Memory ....................................................................... 4-16 Installing the Optional Memory......................................................................... 4-18 Removing the MDC Card .................................................................................. 4-19 Installing the MDC Card.................................................................................... 4-21

4.2

HDD ..................................................................................................................... 4-22 Removing the HDD ........................................................................................... 4-22 Installing the HDD............................................................................................. 4-24

4.3

Speaker Cover and Keyboard............................................................................... 4-24 Removing the Speaker Cover and Keyboard..................................................... 4-25 Installing the Speaker Cover and Keyboard ...................................................... 4-26

4.4

Bluetooth Card ..................................................................................................... 4-27 Removing the Bluetooth Card ........................................................................... 4-27

x

Satellite A100/A105 / TECRA A7 Maintenance Manual

Installing the Bluetooth Card ............................................................................. 4-28 4.5

Wireless LAN Card .............................................................................................. 4-29 Removing the Wireless LAN Card .................................................................... 4-29 Installing the Wireless LAN Card...................................................................... 4-30

4.6

ODD Bay Module ................................................................................................ 4-31 Removing the ODD Bay Module ...................................................................... 4-31 Installing the ODD Bay Module ........................................................................ 4-32 Disassembling the ODD Bay Module................................................................ 4-33 Assembling the ODD Bay Module .................................................................... 4-33

4.7

Display Assembly ..................................................................................................... 4-34 Removing the Display Assembly....................................................................... 4-34 Installing the Display Assembly ........................................................................ 4-35

4.8

Top Cover............................................................................................................. 4-36 Removing the Top Cover................................................................................... 4-36 Installing the Top Cover .................................................................................... 4-38

4.9

CPU Cooling Module and Fan ............................................................................. 4-39 Removing the CPU Cooling and Fan (for VGA Card Model) .......................... 4-39 Installing the CPU Cooling and Fan (for VGA Card Model)............................ 4-41 Removing the CPU Cooling and Fan................................................................. 4-42 Installing the CPU Cooling and Fan .................................................................. 4-43

4.10

VGA Card (for VGA Card Model Only) ............................................................. 4-44 Removing the VGA Card................................................................................... 4-44 Installing the VGA Card .................................................................................... 4-45

4.11

CPU ...................................................................................................................... 4-46 Removing the CPU ............................................................................................ 4-46 Installing the CPU.............................................................................................. 4-47

4.12

USB Board, Finger Print Board and Print Board ................................................. 4-49 Removing the USB Board, Finger Print Board and Print Board ....................... 4-49 Installing the USB Board, Finger Print Board and Print Board......................... 4-50

4.13

System Board, MIC cable, AC IN cable .............................................................. 4-51 Removing the System Board, MIC cable, AC IN cable…. ............................... 4-51

Satellite A100/A105 / TECRA A7 Maintenance Manual

xi

Installing the System Board, MIC cable, AC IN cable….................................. 4-52 4.14

Display Mask........................................................................................................ 4-53 Removing the 15.4-inch LCD Display Mask .................................................... 4-53 Installing the 15.4-inch LCD Display Mask...................................................... 4-54

4.15

FL Inverter Board................................................................................................. 4-55 Removing the FL Inverter Board....................................................................... 4-55 Installing the FL Inverter Board ........................................................................ 4-56

4.16

LCD Modules ....................................................................................................... 4-57 Removing the 15.4-inch LCD module............................................................... 4-57 Installing the 15.4-inch LCD Module................................................................ 4-59

4.17

Speakers ............................................................................................................... 4-60 Removing the Speakers...................................................................................... 4-60 Installing the Speakers ....................................................................................... 4-60

4.18

Switch Cover and Switch Board .......................................................................... 4-61 Removing the Switch Cover and Switch Board (For Consumer Model) .......... 4-61 Installing the Switch Cover and Switch Board.................................................. 4-62 Removing the Switch Cover and Switch Board (For Commercial Model) ....... 4-63 Installing the Switch Cover and Switch Board.................................................. 4-64

4.19

Touch Pad and Touch Pad Board ........................................................................ 4-65 Removing the Touch Pad and Touch Pad Board (For Consumer Model)......... 4-65 Installing the Touch Pad and Touch Pad Board ................................................ 4-66 Removing the Touch Pad and Touch Pad Board (For Commercial Model)...... 4-67 Installing the Touch Pad and Touch Pad Board ................................................ 4-68

xii

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices Appendix A

Handling the LCD Module ........................................................................... A-1

Appendix B

Board Layout ................................................................................................ B-1

Appendix C

Keyboard Scan/Character Codes .................................................................. C-1

Appendix D

Key Layout.................................................................................................... D-1

Appendix E

Wiring Diagrams............................................................................................E-1

Appendix F

BIOS Rewrite Procedures .............................................................................. F-1

Appendix G

EC/KBC Rewrite Procedures........................................................................ G-1

Appendix H

GREASE NFORMATION ………………………..………………………H-1

Satellite A100/A105 / TECRA A7 Maintenance Manual

xiii

Chapter 1 Hardware Overview

1 Hardware Overview

ii

Satellite A100/A105 / TECRA A7

Maintenance Manual

1 Hardware Overview

Chapter 1

Contents

1.1 Features ............................................................................................................................... 1 1.2 System Unit Components ................................................................................................... 9 1.3 2.5-inch HDD.................................................................................................................... 15 1.4 DVD-ROM Drive ............................................................................................................. 16 1.5 CD-RW/DVD-ROM Drive ............................................................................................... 17 1.6 DVD Super Multi (+-R Double Layer)............................................................................. 18 1.7 Power Supply .................................................................................................................... 19 1.8 Batteries ............................................................................................................................ 20 1.1.1

Main Battery.......................................................................................... 20

1.1.2

Battery Charging Control ...................................................................... 20

1.1.3

RTC Battery .......................................................................................... 21

Satellite A100/A105 / TECRA A7

Maintenance Manual

iii

1 Hardware Overview

Figures Figure 1- 1 id Parts description placement ..............................................................................6 Figure 1- 2 The computer Block diagram ................................................................................7 Figure 1- 3 System Board configuration .................................................................................8 Figure 1- 4 System unit block diagram ....................................................................................9 Figure 1- 5 2.5-inch HDD .....................................................................................................15 Figure 1- 6 DVD-ROM drive ................................................................................................16

Tables Table 1- 1 2.5-inch HDD specifications................................................................................15 Table 1- 2 DVD-ROM drive specifications ..........................................................................16 Table 1- 3 CD-RW/DVD-ROM drive specifications ............................................................17 Table 1- 4 DVD Super Multi drive (+-R Double Layer) specifications ...............................18 Table 1- 5 Battery specifications...........................................................................................20 Table 1-6 Quick/normal charging time .................................................................................21

iv

Satellite A100/A105 / TECRA A7

Maintenance Manual

1.1 Features

1 Hardware Overview

1.1 Features The Toshiba Satellite A100/A105 / TECRA A7 is a full size notebook PC based on the Intel Pentinm M (Dothan) and Celeron M processor, providing high-speed processing capabilities and advanced features. The computer employs a Lithium Ion battery that allows it to be batteryoperated for a longer period of time. The display uses 15.4-inch WXGA and WSXGA+ LCD panel, at a resolution of 1280 by 800 pixels (WXGA) and 1680 by 1050 pixels (WSXGA+), The uPGA socket supports BTO/CTO for the CPU so that the system can be designed to suit your needs.

The computer has the following features. ‰ Processor The CPU is the Intel Yonah Processor and Intel Yonah based Celeron M.

Intel Yonah Processor (667MHz) T2300(1.66G)/T2400(1.83G)/T2500(2G)/T2600(2.16G)/T2700(2.33G) /T1300(1.66G)/T1400(1.83G) Hz Intel Yonah based Celeron M Processor (533MHz) 410/420/430 ‰ Host bridge system controller System controller: Intel 945GM/945PM/940GML ‰ Memory The computer has two SO DIMMs slot comes standard with DDRII 4200 module. It supports PC2-4200 and uses SO DIMMs (DDRII SDRAM) driven at 1.8 V, accepting BTO/CTO for your memory requirements. It can incorporate up to 4 GB of main memory. using the following sizes of memory modules: y 256 MB (16M×16×8P)/533/667 MHZ y 512 MB (32M×16×8P)/533/667 MHZ y 1024 MB (64Mx16x8P)/533/667 MHZ

Satellite A100/A105 / TECRA A7

Maintenance Manual

1

1 Hardware Overview

1.1 Features

‰ Hard Disk Drive (HDD) The computer accommodates one 2.5-inch HDD with any of the following storage capacities: y 40 GB (9.5 mm thick) SATA (5,400rpm) y 60 GB (9.5 mm thick) SATA (5,400rpm/7200rpm) y 80 GB (9.5 mm thick) SATA (5,400rpm/7200rpm) y 100 GB (9.5 mm thick) SATA (5,400rpm/7200rpm) y 120 GB (9.5 mm thick) SATA (5400rpm) ‰ ODD The ODD can accommodate a DVD-ROM, CD-RW/DVD ROM, DVD Super Multi (+-R Double Layer)drives. ‰ Display The LCD displays available come in the following four sizes: y 15.4” WXGA-Non CSV/15.4” WXGA-CSV/15.4” WXGA-CSV(200 NITs High brightness) /15.4” WXGA-HHCSV(490 NITs High brightness) color display, resolution 1280×800,262,144 colors with dithering. y ‰ Keyboard The keyboard has 29 kinds countries key. ‰ Batteries The computer has a removable 6/9/12 Cell Lithium Ion battery pack and an internal RTC battery (rechargeable). ‰ Universal Serial Bus (USB) ports The computer has four USB 2.0 ports, It is supported to daisy-chain a maximum of 127 USB devices. The serial data transfer rate is 480 Mbps or 12 Mbps and 1.5 Mbps These ports support PnP installation and hot plugging.

2

Satellite A100/A105 / TECRA A7

Maintenance Manual

1.1 Features

1 Hardware Overview

‰ External monitor port A 15-pin external monitor port is provided, through which the computer automatically recognizes an external VESA DDC 2B compatible monitor. ‰ PC Card slot A PC Card slot is provided to hold PC Card Standard Type II (5.0 mm) card, capable of using a variety of PC Cards including 16-bit Multiple Function PC Cards and 32-bit CardBus cards. PC card HDD boot does Not be supported.

‰ SD/MS/MS Pro/MMC/XD Card slot(BTO) This slot is for your memory card requirements to provide memory card read on your computer

‰ Toshiba Pointing Device(BTO) Toshiba Pointing Device has one kind of Synaptice TouchPad with two button and One kind of Dual mode Pad for BTO . ‰ Sound system The ALC861 integrated audio controller supports multimedia. The sound system contains the following: y Stereo speakers y Headphone jack y Internal microphone y External microphone jack ‰ LAN The internal LAN board supports 10/100 Mbit and Giga-bit for BTO, enabling connection to a LAN at up to 1GMbps. It also supports Wake-up On LAN From S3/S4/S5 and PXE boot support. The LAN board has the RJ45 jack to directly accommodate a LAN cable.

Satellite A100/A105 / TECRA A7

Maintenance Manual

3

1 Hardware Overview

1.1 Features

‰ Wireless LAN The internal Mini Card slot supports IEEE802.11a/g(11ch)/ IEEE802.11g(11ch)/ IEEE802.11a/g(13ch)/ IEEE802.11g(13ch)/IEEE802.11a/g(14ch)/ IEEE802.11g(14ch) card. The Antenna has three wires dual band antenna support with Blue tooth for BTO. ‰ Internal Modem The computer contains a MDC, enabling data and fax communication. It supports ITUT V.90 (for rest countries )/V.92(America, Canada,UK,Germany,France) The transfer rates are 56 Kbps for data reception, 33.6 Kbps for data transmission, and 14,400 bps for fax transmission. Note, however, that the actual speed depends on the line quality. The RJ11 modem jack is used to accommodate a telephone line. ‰ IEEE 1394(BTO) The IEEE 1394 serial data transfer rate is 400 Mbps, These port support hot plugging. ‰ Finger Print(BTO) This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password to the fingerprint authentication device, it is no longer necessary to input the password from the keyboard. Just by swiping the finger against the fingerprint sensor.

‰ TPM 1.2 The Trusted Platform Module (TPM) is an integrated circuit and software platform that provides computer manufacturers with the core components of a subsystem used to assure authenticity, integrity and confidentiality in e-commerce transactions and Internet communications.

‰ CD Key(BTO) The CD Key supports to play Audio CD directly.

‰ PCI Express Slot(BTO)

4

Satellite A100/A105 / TECRA A7

Maintenance Manual

1.1 Features

1 Hardware Overview

The ICH7 provides PCI Express root ports which are compliant to the PCI Express Base Specification ,Revision 1.0a.The Root Port supports 2.5Gb/s bandwidth in each direction (5 Gb/s concurrent) and two virtual channels for full isochronous data support. ‰ Parallel Port(BTO) The Parallel Port is optional integrated device. to supported connect a printer or another parallel device. The port is IEEE-1284 compliant and supports Extended Capabilities Port (ECP).

‰ Fast Serial Infrared (FIR) communications port(BTO) The FIR Port is optional integrated device. It provided an IrDA 1.1 compatible FIR port , enabling wireless communication at a high speed of 1.15 or 4 Mbps.

Satellite A100/A105 / TECRA A7

Maintenance Manual

5

1 Hardware Overview

1.1 Features

‰ Figures 1-1/1-2/1-3 and 1-4 show the computer and its system unit configuration, respectively.

Figure 1- 1 id Parts description placement

6

Satellite A100/A105 / TECRA A7

Maintenance Manual

1.1 Features

1 Hardware Overview

ICS9L P306

Yonah

Cl ock generator

(uFCPGA )

FSB,533/667MHz

S-video LCM

Calistoga

CRT

945GM/PM 1466 uFCB GA

1.8V,DDR2Interface,533/667MHz

AZALIA

MDC/Modem Module56K BA TTERY RJ11

MIC JACK HP JACK

3.3V,PCI_Interface,33MHz

ICH7-M 652 B GA

3.3V, LPC_Interface,33MHz

US B 7

USB6

DO CKIN G

Exp res s Card

USB5

FINGER PRINT

USB4

Blueto oth

USB 3 CON N D

US B 2 CON N C

U SB 1 CO N N B

U SB 0 CO N N A

3.3V,AZALIA PORT REPLICATOR

(IMVP-6 VR)

1.8V,DDR2Interface,533/667MHz

DMIx4

Primary_IDE

ODD

System Charger &

DDR2_SODIMM1

SATA

HDD

DC/DC System po wer

DDR2_SODIMM0

PCI_EXPRESS INTEL 10/10082562GZ 1G82573E(ATM) 82573L(w/oATM)

RJ45

MINI CA RD Wireless LA N

A NT

Cardb us SL OT A

A NT

SMSC K BC1100

3-AXISSENSOR

BIOS FL ASH ROM

SERIAL PORT

SPEAKER

EXPRESSCARD

CA RD B US TI_ PCI7412/ 4512 (CO-LA YOUT)

TPM 1.2

Card reader 1394 CONN CONN

SMSC SIO 1036

PARA LLEL PORT

FIR CIR

Figure 1- 2 The computer Block diagram

Satellite A100/A105 / TECRA A7

Maintenance Manual

7

1.1 Features

1 Hardware Overview

Rj 45 DC- I N USB* 2

Par al l el Kensi ngt on Rj 11

Bat t er y

RGB

Speak er

Speak er

ODD

S- Vi deo 1394

PC Car d* 1 Expr es s Car d * 1 5 in 1 Car d Reader FI R/ CI R

Vol ume

HDD

USB* 2 Ki l l SW

Mi c r ophone Headphone

Figure 1- 3 System Board configuration

Satellite A100/A105 / TECRA A7

Maintenance Manual

8

1.2 System Unit Components

1 Hardware Overview

1.2 System Unit Components Figure 1-4 is a block diagram of the system unit.

Cl oc k Gener at or ( I CS9LP306)

CPU : I nt el Yonah 1. 66G. . . . . . 2. 33GHZ uPGA

Max 6657 Themal Sens or

CPU V I D

DC

I SL6218

Pc4200 DDRI I 533/ 667 Mhz

S- Vi deo

Ex pans i on Memor y 256/ 512/ 1024

Ex pans i on Memor y 256/ 512/ 1024

I nt el 945GM/ PM 940GML Nor t h Br i dge

CRT

VRAM

DMI L AN Co n t . 10/ 100 8 2 5 6 2 GZ 1G 82573E

SM Bu s Co n t .

I nt - HDD SATA 40- 120GB 9. 5mm

LCD 15. 4"

LVDS

I CH7- M Sout h Br i dge

SATA

Mi ni PCI Sl ot 802. 11g, a/ g Wi r el es s Lan

An t e n n a

EEPROM

CARD BUS Co n t r o l l e r TI _ PCI 7 4 1 2 / PCI 4 5 1 2

PCMCI A

Rj 4 5

Ac 97

I DE Cont .

MDC Modem CODEC ALC 861

5i n1 Ca r d Re a d e r

1394 CNNx 1

Rj 11

TPA6011

Speak er MI C Headphone

USB Cont . ( 02)

DVD- ROM DVD- CD/ RW COMBO DVD Super Mul t i ( +- R Doubl e l ay er )

USB USB

PCI - PC Br i dge

USB

I nt er nal LPC

Fl as h ROM

EC/ KBC ( KBC1100)

3- AXI S SENSOR

I 2C

KPA AC 1269A

SMSC SI O 1036

SERI AL PORT

St i c k poi nt K/ B Mai n Bat t er y

TPM 1. 2

FI R

PARALLEL PORT

EEPROM

CI R

Figure 1- 4 System unit block diagram

Satellite A100/A105 / TECRA A7

Maintenance Manual

9

1 Hardware Overview

1.2 System Unit Components

The system unit of the computer consists of the following components: ‰ Processor: Intel Yonah Processor and Yonah Based Celeron M y Intel Yonah Processor (667MHz) − Core speed: 1.66/1.83/2.0/2.16/2.33 GHz − System bus: 667 MHz − On-die level 2 cache 2 MB − Advanced Power Management features including Enhanced Intel ® SpeedStep ® technology y Yonah Based Celeron-M (533MHz) − Core speed: TBD − System bus: 533 MHz − On-die level 2 cache 1 MB ‰ Memory Two expansion memory slots were provided, They can hold 256/512/1024MB expansion memory modules available as options to grow up to 4.0 GB. y PC2-4200 /533/667MHz DDRII SDRAM supported y 256/512/1024MB modules supported − 256 MB (16M x 16 x 8P) − 512 MB (32M x 16 x 8P) − 1024 MB (64M x 8 x 16P) y 1.8 volt operation y No parity bit y 64-bit data transfer

10

Satellite A100/A105 / TECRA A7

Maintenance Manual

1.2 System Unit Components

1 Hardware Overview

‰ BIOS ROM (flash EEPROM) y 8Mb x 1 chip (1024KB flash parts) − − − − − − − − − − − − − − − − −

40Kb used for EC BIOS 35Kb used for PNP 3Kb used for display 15Kb used for logo 16Kb used for setup 10Kb used for setup nodes 1Kb used for decompress code 1Kb used for boot block 2Kb used for TPM 64Kb used for 23Kb used for miser 237Kb used for VGA BIOS 42Kb used for PXE 14Kb used for string 47Kb used for ROMEXEC 133Kb used for BIOS code 6Kb used for mini loader

‰ System controllers y North Bridge: Intel 945 GM/PM/940GML − − − − − − − − − −

CPU interface and control System Memory Support PCI Express* Graphics (PEG) Interface Integrated Display Interface Support Internal Graphics Features Direct Media Interface (DMI) Power Management Serial ATA Interface ICH7 Audio Control SMBus 2.0/SMLink Interface

y South Bridge: ICH7-M − Direct Media Interface (DMI) − PCI Express* Interface − Serial ATA (SATA) Controller

Satellite A100/A105 / TECRA A7

Maintenance Manual

11

1 Hardware Overview

1.2 System Unit Components − − − − − − − − − − − − − − − −

Advanced Host Controller Interface (AHCI) PCI Interface IDE Interface Low Pin Count (LPC) Interface Compatibility Modules Advanced Programmable Interrupt Controller (APIC) Universal Serial Bus (USB) Controller Lan Controller Alert Standard Format (ASF) Management Controller RTC GPIO Enhanced Power Management Manageability System Management Bus (SMBus 2.0) Intel High Definition Audio Controller AC ’97 2.3 Controller

− − − −

CardBus/PC Card controller 16-bit PCMCIA and 32-bit CardBus. SD/MS/MS Pro/MMC/XD Card controller IEEE 1394 Controller

‰ PC Card controller y TI_PCI7412

‰ Audio Controller The ALC861 integrated audio controller supports multimedia. The sound system feature contains the following: y 4 Stereo DACs support 16/20/24-bit PCM format for 7.1 channel audio solution. y 1 stereo ADCs support 16-bit PCM forma.t y Front/Surround /Cen/Lfe/Side-Surround DACs support independent 48KHz/96KHz sample rate. y ADC support 48K/96K sample rate. y FRONT(port-D),LINE2(port-E)and MIC2(port-F) are stereo input and output re-tasking. y High quality differential CD input. y 2 jack detection pins each supports up to 4 jacks can be detected. y Support 48KHz/96KHz of S/PDIF output. y Supports analog PCBEEP input. y Integrates digital BEEP generator.

12

Satellite A100/A105 / TECRA A7

Maintenance Manual

1.2 System Unit Components

1 Hardware Overview

y Power support : Digital : 3.3V ; Analog : 5.0V y 48-ping LQFP package. ‰ KBC/EC (Keyboard Controller/Embedded Controller) A single KBC 1100L chip is used to serve as KBC/ EC and Super IO. y KBC − Scan controller function − Interface controller function y EC − − − − − − − − − − − − ‰ Battery EE PROM

Power supply sequence control Overheat shutdown support LED control Beep control Device ON/OFF Cooling fan speed control Universal I/O port Battery capacity check Flash memory reprogramming function EC access interface I2C communication control

y 24C02 equivalent (128 words x 16 bits, I2C interface) integrated in the battery pack − Storing records of battery use ‰ Clock Generator y ICS9LP306 − Generating the clock signal required for the system ‰ Modem Controller y Built-in MDC card with askey y Functions of the modem controller: − Digital signal conductor protection − Ring wake-up support − Communication codes supported:

Satellite A100/A105 / TECRA A7

Maintenance Manual

13

1 Hardware Overview

1.2 System Unit Components

For data communication: V.90(China)/V.92 data rates: 28kbps/56kbps V.34 Extended rates: 33.6K/2400/V.32 turbo, V.32bits,and fallbacks For fax: V.34,V.17,V.29 V.27 and V.21 Channel 2 V.253 Class 1 fax -AC97 interface ‰ LAN controller y 82562GZ − IEEE 802.3 10BASE-T/100BASE-TX compliant physical layer interface − IEEE 802.3u Auto-Negotiation support − Digital Adaptive Equalization control − 10BASE-T auto-polarity correction − LAN Connect interface − Automatic detection of “unplugged mode” − Remote boot(PXE 2.1) − Smart power down when link is not detected y 82573E − − − − − − − − ‰

PCIe Power Management Peak bandwidth 2 gigabytes/second per direction Digital Adaptive Equalization control Optimized transmit and receive queues On-board microcontroller SNMP and RMON statistic counters SDG 3.0, WfM 3.0, and PC2001 compliance Wake on LAN support

Wireless LAN controller

y Support following 2 kinds of mini PCI wireless LAN cards. − IEEE 802.11g − IEEE 802.11a/g y Transfer Rate − IEEE 802.11a/g: Standard 54M bps − IEEE 802.11g: Standard 54M bps y Frequency Channel − IEEE802.11a/g: 5.4GHz − IEEE802.11g: 2.4GHz

14

Satellite A100/A105 / TECRA A7

Maintenance Manual

1.3 2.5-inch HDD

1 Hardware Overview

1.3 2.5-inch HDD The computer contains an extremely low-profile and lightweight, high-performance HDD. The HDD incorporates a 2.5-inch magnetic disk and mini-Winchester type magnetic heads. Storage capacities supported are 40,60,80,100/120 GB. The HDD interface conforming to Serial ATA (for 40/60/80/100/120 GB). The HDD is shown in Figure 1-5 and some of its specifications are listed in Table 1-1.

Figure 1- 5 2.5-inch HDD

Table 1- 1 2.5-inch HDD specifications Specifications

Item Capacity (GB)

40GB

60GB

80GB

Rotational speed (RPM)

5400 rpm

User data sectors

78,140,160

117,210,240

156,301,488

512

512

512

Bytes/sector

5400 rpm

Satellite A100/A105 / TECRA A7

7200 rpm

5400 rpm

7200 rpm

Maintenance Manual

100GB 5400 rpm

7200 rpm

195,371,568 512

120GB 5400 rpm

234,442,648 512

15

1.6 DVD Super Multi (+-R Double Layer)

1 Hardware Overview

1.4 DVD-ROM Drive The DVD-ROM drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. The drive provides high-speed data transfer, playing back a DVD at up to 8x speed and reading up to 10,820 Kbytes per second from DVD-ROM and 3,600 Kbytes per second from CD-ROM. The DVD-ROM drive is shown in Figure 1-6 and its specifications are listed in Table 1-2.

Figure 1- 6 DVD-ROM drive Table 1- 2 DVD-ROM drive specifications Item Data transfer rate (Mbytes/s)

DVD-ROM 33.3 (U-DMA transfer mode 2) 16.7 (PIO mode 4, Multiword DMA mode 2)

Access time (ms) Average random access

100ms

Data buffer size (Kbytes)

512KB

Formats supported

DVD-R/W(Read only), DVD-R (Read only),DVDRAM , CD-ROM, CD-R,CD-DA,CD-I,CD(Photo-CD,CDEXTRA,CD-R,CD-RW,Portiolio) CD-R (Read only), CD-RW (Read only)

Satellite A100/A105 / TECRA A7

Maintenance Manual

16

1.5 CD-RW/DVD-ROM Drive

1 Hardware Overview

1.5 CD-RW/DVD-ROM Drive The CD-RW/DVD-ROM drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed and HS CD-RW at 10x speed and US CD-RW at 24x speed and CD-RW at 4x speed. The specifications of the CD-RW/DVD-ROM drive are listed in Table 1-3.

Table 1- 3 CD-RW/DVD-ROM drive specifications Item Data transfer rate (Mbytes/s)

Access time (ms) Average random access

DVD-ROM mode

CD-RW mode

33.3 (U-DMA transfer mode 2) 16.7 (PIO mode 4, Multiword DMA mode 2)

150 ms

Data buffer size (Mbytes)

2MB

Formats supported

DVD:

130 ms

DVD-ROM,DVD-R,DVD-RAM

CD: CD-DA,CD+(E)G,CD-MIDI,CD-TEXT,CD-ROM,CD-ROM XA,MIXED MODE CD,CD-I,CD-I Bridge(Photo CD,Video CD),Muitisession CD(Photo CD,CD-EXTRA,Portfolio,CD-R,CD-RW),CD-R,CD-RW

Satellite A100/A105 / TECRA A7

Maintenance Manual

17

1.6 DVD Super Multi (+-R Double Layer)

1 Hardware Overview

1.6 DVD Super Multi (+-R Double Layer) The DVD Super Multi drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed and CD-RW at 4x speed and US CD-RW at 16x speed and High speed CD-RW at 10x speed and DVD-R at 8x speed and DVD-RW at 6x speed and DVD+R at 8x speed and DVD+R (Double Layer) at 4x speed and DVD-R (Double Layer) at 4x speed and DVD+RW at 8x speed and DVD-RAM at 5x speed. The specifications of the DVD Super Multi (+-R Double Layer) drive are listed in Table 1-4.

Table 1- 4 DVD Super Multi drive (+-R Double Layer) specifications Item Data transfer rate (Mbytes/s)

DVD-ROM mode

CD-ROM mode

33.3 (U-DMA transfer mode 2) 16.6 (PIO mode 4, Multiword DMA mode 2)

Access time (ms) Average random access Data buffer size (Mbytes)

2MB

Formats supported

DVD:

130

130

DVD-VIDEO,DVD-ROM,DVD-R,DVD-RW,DVD-RAM, DVD+R,DVD+-R(Double Layer),DVD+RW. CD: CD-DA,CD-ROM, CD-R,CD-RW,CD-ROMXA, PhotoCD(muitiSession),Video CD,CD-Extra(CD+),CD-Text

Satellite A100/A105 / TECRA A7

Maintenance Manual

18

1.7 Power Supply

1 Hardware Overview

1.7 Power Supply The power supply unit provides many different voltages for the system board and performs the following functions: 1. Power input monitor y Checks whether the DC power supply (AC adapter) is connected to the computer. y Checks whether the battery pack is connected to the computer. y Monitors the DC power supply input voltage (AC Adapter output voltage). 2. Power supply's internal control y Turns on and off the battery pack charging power supply. y Issues a charging current instruction to the PWM control IC of the battery pack charging power supply. y Controls the supply of DC power supply input (AC Adapter output) to the power supply unit. y Controls the supply of power to the system block (load/logic circuit side). y Controls forced shutdown if the power supply malfunctions. 3. Logic circuit control y Instructs the gate array to enable/disable tuning the power on. y Controls power-on/off operation. 4. Status display y Turns on the Power LED (in Blue or Green or AMBER). y Battery indicator (in Blue or Green or AMBER or AMBER Flash). 5. External interface y Performs communication through the I2C bus (via the internal EC/KBC). y Transfers the power supply operation mode. 6. Output monitor y Monitors the voltage output to the system block (load/logic circuit side). y Monitors the voltage, over voltage, input/output current of the battery pack. y Monitors the internal temperature of the battery pack. y Monitors the supply voltage from the AC adapter.

Satellite A100/A105 / TECRA A7

Maintenance Manual

19

1 Hardware Overview

1.8 Batteries

1.8 Batteries The computer has the following three types of batteries: ‰ Main battery pack ‰ Real time clock (RTC) battery Table 1-5 lists the specifications of these batteries. Table 1- 5 Battery specifications Battery name

Material

Output voltage

Capacity

6 Cell

Lithium Ion

10.8 V

4000 mAh

9 Cell

Lithium Ion

10.8 V

6000 mAh

12 Cell

Lithium Ion

10.8 V

8600 mAh

Lithium Ion

3.0 V

14 mAh

Main battery pack

RTC battery

1.1.1

Main Battery The main battery pack serves as the computer's main power source when the AC adapter is not attached. The main battery maintains the state of the computer so that it can resume it.

1.1.2

Battery Charging Control Battery charging is controlled by LPC 47N249. When the AC adapter and battery pack are attached to the computer, the LPC 47N249 controls the charge on/off state and detects a full charge.

‰ Battery Charge When the AC adapter is attached, the battery is charged by off-state charge when the system is powered off or by on-state charge when it is powered on.

20

Satellite A100/A105 / TECRA A7

Maintenance Manual

1.8 Batteries

1 Hardware Overview

Table 1-6 Quick/normal charging time State

Charge time

Off-state charge

6/9/12 Cell

About 4 hours max

On-state charge

6/9/12 Cell

About 4~10 hours max

NOTE: The time required for normal charge depends on the power consumption by the system. Using the fluorescent lamp and frequently accessing the disk consume much power and lengthen the charge time. Any of the following cases stops battery charge: 1.

The battery becomes fully charged.

2.

The AC adapter or battery pack is removed.

3.

The battery or AC adapter voltage is abnormal.

‰ Detection of full charge A full charge is detected only when the battery is being charged by quick or normal charge. A full charge is detected when either of the following conditions is met:

1.1.3

1.

The current in the battery charging circuit drops below the predetermined value.

2.

The charging time exceeds the fixed limit.

RTC Battery

The RTC battery provides power to keep the current date, time and other system information in memory while the computer is turned off.

Satellite A100/A105 / Satellite Pro A100 / EQUIUM A100

Maintenance Manual

21

2 Troubleshooting 2

Chapter 2 Troubleshooting

2-i

Satellite A100/A105 / TECRA A7 Maintenance Manual

2 Troubleshooting

Chapter 2

Contents

2.1

Outline.................................................................................................................... 2-1

2.2

Basic Flowchart...................................................................................................... 2-2

2.3

Power Supply ......................................................................................................... 2-6 Procedure 1 Power Icon Check....................................................................... 2-6 Procedure 2 Connection Check....................................................................... 2-8 Procedure 3 Replacement Check .................................................................... 2-8

2.4

System Board ......................................................................................................... 2-9 Procedure 3 Replacement Check ................................................................. 2-11

2.5

2.5-inch HDD ....................................................................................................... 2-12 Procedure 1 Message Check ......................................................................... 2-12 Procedure 2 Partition Check .......................................................................... 2-12 Procedure 3Format Check.............................................................................. 2-14 Procedure 4Test Program Check ................................................................... 2-15 Procedure 5Connector Check and Replacement Check................................. 2-16

2.6

Keyboard .............................................................................................................. 2-17 Procedure 1 Test Program Check .................................................................. 2-17 Procedure 2 Connector Check and Replacement Check................................ 2-17

2.7

Display ................................................................................................................. 2-18 Procedure 1External Monitor Check ............................................................. 2-18 Procedure 2Test Program Check ................................................................... 2-18 Procedure 3Connector Check and Replacement Check................................. 2-18

2.8

ODD (Optical Disk Drive) ................................................................................... 2-20 Procedure 1ODD Cleaning Check ................................................................. 2-20 Procedure 2Test Program Check ................................................................... 2-20 Procedure 3Connector Check and Replacement Check................................. 2-20

2.9

LAN...................................................................................................................... 2-22 Procedure 1Test Program Check ................................................................... 2-22 Procedure 2Connector Check and Replacement Check................................. 2-22

2.10

SD/MS/MS pro/MMC/XD Card(Optional) ......................................................... 2-23 Procedure 1Test Program Check ................................................................... 2-23

2-ii

Satellite A100/A105 / TECRA A7 Maintenance Manual

2 Troubleshooting

Procedure 2Connector Check ........................................................................ 2-23 2.11

Finger Print(Optional) .......................................................................................... 2-24 Procedure 1Test Program Check ................................................................... 2-24 Procedure 2Connector Check ........................................................................ 2-24

2.12

3D Sensor ............................................................................................................. 2-25 Procedure 1Test Program Check ................................................................... 2-25 Procedure 2Replacement Check .................................................................... 2-25

2.13

Parallel Port(Optional) ......................................................................................... 2-26 Procedure 1Test Program Check ................................................................... 2-26 Procedure 2Connector Check ........................................................................ 2-26

2.14

Audio Test ............................................................................................................ 2-27 Procedure 1 Test Program Check .................................................................. 2-27 Procedure 2 Connector Check and Replacement Check................................ 2-27

2.15

IEEE 1394 Test .................................................................................................... 2-28 Procedure 1Test Program Check ................................................................... 2-28 Procedure 2Connector Check ........................................................................ 2-28

2.16

Cooling Module.................................................................................................... 2-29 Procedure 1Test Program Check ................................................................... 2-29 Procedure 2Connector Check and Replacement Check................................. 2-29

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-iii

2 Troubleshooting

Figures Figure 2-1

Basic flowchart .............................................................................................. 2-3

Tables Table 2-1

2-iv

HDD error code and status........................................................................... 2-15

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.1 Outline

2 Troubleshooting

2.1 Outline This chapter describes the fault diagnosis procedures for field replaceable units (FRUs) in the computer. The FRUs covered here are as follows: 1. System board 2. 2.5-inch HDD 4. Display 5. ODD drive 7. SD/MS/MS pro/MMC/XD 9. Speaker 9. IEEE 1394

3. Keyboard 6. LAN 8. Finger Print 10. Cooling module

See Chapter 4 for the procedures to replace FRUs and Chapter 3 for the procedures to use test programs The following tools are required to perform the diagnostic procedures: 1. Diagnostics (maintenance test program) disk 2. Phillips screwdrivers (2 mm, 2.5 mm) 3. Cleaning disk kit (for ODD drive cleaning) 4. Bootable CD 5. PC Card loopback connector 6. Multimeter 7. External monitor 8. Headphone 9. Microphone 10. A-BEX TEST DVD 11. Music CD 12. DVD TSD-1 (TOSHIBA EMI DVD Test Media)

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-1

2 Troubleshooting

2.2 Basic Flowchart

2.2 Basic Flowchart The basic flowchart in Figure 2-1 serves as a guide for identifying a possibly faulty FRU. Before going through the diagnostic flowchart steps, verify the following: ‰ Ask the user if a password has been registered and, if so, ask him or her to enter the password. If the user has forgotten the system password, use a jump wire to make a short circuit on M/B C88 , then turn the computer power on. When booted, the computer overrides password protection and automatically erases the current password. ‰ Make sure the Windows® XP Home Edition has been installed on the HDD. Any other operating system can cause the computer to malfunction. ‰ Make sure any piece of optional equipment has been installed.

2-2

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.2 Basic Flowchart

2 Troubleshooting

Star t Connect the AC Adapter

No

Follow the power supply diagnostic procedure in Section 2.3

DC IN LED on ?? Yes No

Follow the power supply diagnostic procedure in Section 2.3

BATTERY LED on ?? Yes Turn the power on. Yes Any error message displayed ??

Follow the system board diagnostic procedure in Section 2.4

No No

Message "In Touch with Tomorrow Toshiba" displayed

Follow the display diagnostic procedure in Section 2.7

Yes Yes "Password=" displayed ??

See the previous page to delete the password.

No OS started ?? No

Follow the HDD diagnostic procedure in Section 2.5

Yes 1 Figure 2-1

Basic flowchart(1/2)

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-3

2 Troubleshooting

2.2 Basic Flowchart

1 No Keyboard works well ??

Follow the keyboard diagnostic procedure in Section 2.6

Insert Bootable CD into ODD

No

Diagnostic Program Loaded ??

Follow the ODD diagnostic procedure in Section 2.8

Yes Perform each test with the diagnostic program.

Any error detected by the diagnostic program ??

Yes

Identify the test resulting in the error and perform the appropriate diagnostic procedures

Yes

Identify the test resulting in the error and perform the appropriate diagnostic procedures

No Perform the continuous test to check if the error is intermittent.

Any error detected by the diagnostic program ?? No The system is normal. END

Figure 2-1

2-4

Basic flowchart (2/2)

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.2 Basic Flowchart

2 Troubleshooting

If the diagnostic program cannot detect an error, the error may be intermittent. Run the continuous test program repeatedly to isolate the problem. Check the log utilities function to confirm which diagnostic test detected the error, then perform the appropriate troubleshooting procedures as follows: 1. If an error is detected by the System test, Memory test, Async test, Printer test, Sound test, or Real Timer test, follow the system board troubleshooting procedures in Section 2.4. 2. If an error is detected by the Hard Disk test, follow the HDD troubleshooting procedures in Section 2.5. 3. If an error is detected by the Keyboard test, follow the keyboard troubleshooting procedures in Section 2.6. 4. If an error is detected by the Display test, follow the display troubleshooting procedures in Section 2.7. 5. If an error is detected by the ODD test, follow the ODD troubleshooting procedures in Section 2.8. 6. If an error is detected by the LAN test, follow the LAN troubleshooting procedures in section 2.9. 7. If an error is detected by the SD Card test, follow the SD Card troubleshooting procedures in section 2.10 8. If an error is detected by the Finger Print test, follow the Speaker troubleshooting procedures in section 2.11. 9. If an error is detected by the 3D sensor test, follow the Speaker troubleshooting procedures in section 2.12. 10. If an error is detected by the Parallel test, follow the Speaker troubleshooting procedures in section 2.13. 11. If an error is detected by the Speaker test, follow the Speaker troubleshooting procedures in section 2.14. 12. If an error is detected by the IEEE 1394 test, follow the IEEE 1394 troubleshooting procedures in section 2.15. 13. If an error is detected by the Fan On/Off test, follow the cooling module troubleshooting procedures in Section 2.16.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-5

2 Troubleshooting

2.3 Power Supply

2.3 Power Supply The power supply in the computer controls many functions and components. To check if the power supply is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1

Power Icon Check

Procedure 2

Connection Check

Procedure 3

Replacement Check

Procedure 1 Power Icon Check The following two power LEDs indicate the power supply status: ‰ Battery LED ‰ DC IN LED The power supply controller displays the power supply status through the Battery and DC IN LEDs as in the tables below. ‰ Battery LED Battery LED

Power supply status

On in Amber

Battery being charged

On in Green/Blue

Battery fully charged, with AC adapter connected

Blinking in Amber

Battery low *1 while driving the computer

(at equal intervals) Off

2-6

Else

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.3 Power Supply

2 Troubleshooting

‰ DC IN LED DC IN LED

Power supply status

On in Green/Blue

DC power being supplied (from the AC adapter)

Off

Battery damage and can’t charge during DC-in.

Off

Else

If the DC IN LED off, follow the steps below: 1. Remove the battery pack and the AC adapter to shut off power supply to the computer. 2. Attach the battery and AC adapter back again. If the LED still off, follow the steps below: Check 1

Make sure the DC IN LED goes on in Green or Blue . If it does not, go to Procedure 2.

Check 2

Make sure the Battery LED goes on in Amber or Blue or Green . If it does not, go to Procedure 3.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-7

2 Troubleshooting

2.3 Power Supply

Procedure 2 Connection Check Power is supplied to the system board as illustrated below: System board

AC adaptor AC power cord

AC adaptor cord Battery pack

Follow the steps below to check whether each connector has been connected correctly: Check 1 Make sure the AC adaptor and AC power cord have been firmly plugged into the DC IN 19V socket and wall outlet, respectively. When they have been connected correctly, perform Check 2. Check 2 Connect a new AC adaptor and AC power cord. • If the DC IN LED does not go on, go to Procedure 3. • If the battery LED does not go on, perform Check 3. Check 3 Make sure the battery pack has been correctly installed in the computer. If the battery LED does not go on while the battery pack has been installed correctly, go to Procedure 3. Procedure 3 Replacement Check The system board, power supply board, or CPU may be faulty. Disassemble the computer according to Chapter 4 and follow the steps below: Check 1

Replace the power supply board with a new one. If the battery pack is still not working properly, perform Check 2.

Check 2

Replace the system board with a new one. If the battery pack is still not working properly, perform Check 3.

Check 3

Replace the CPU with a new one.

2-8

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.4

System Board

2 Troubleshooting

2.4 System Board To check if the system board is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Test Program Check Procedure 3 Replacement Check Procedure 1 Message Check When the power is turned on, the system performs the self-diagnostic Power On Self Test (POST) embedded in the BIOS ROM. The POST tests and initializes each IC on the system board. ‰ If an error message appears on the display, perform Check 1. ‰ If there is no error message, go to Procedure 2. ‰ If MS-DOS or Windows XP Home Edition is loaded normally, go to Procedure 3. Check 1

If the following error message is displayed on the screen, press the F1 key as prompted. These errors occur when the system configuration preserved in the RTC memory (generally called CMOS memory) does not match the actual configuration or when the data is lost. If you press the F1 key as prompted by the message, the TSETUP screen appears to set the system configuration. If the error message appears frequently when the power is turned on, replace the RTC battery. If any other error message is displayed, perform Check 2. *** Bad RTC battery *** Check system. Then press [F1] key

Check 2

If the following error message is displayed on the screen, press any key as prompted by the message. The error message appears when either data stored in RAM to be resumed is lost because the battery has been exhausted or the system board is faulty. If any other error message displays, perform Check 3.

Check 3

Resume failure and press any key to continue.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-9

2 Troubleshooting

2-10

2.4 System Board

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.4

System Board

2 Troubleshooting

Procedure 2 Test Program Check The maintenance test program contains several programs for diagnosing the system board and CPU. Execute the following test programs using the procedures described in Chapter 3. 1. System test 2. Memory test 3. Keyboard test 4. Display test 5. Hard Disk test 6. Mouse test 7. SD Card/Memory stick test 8. ODD test 9. Sound test 10. LAN test If an error is detected during these tests, go to Procedure 3. Procedure 3 Replacement Check The system board, memory, or CPU may be defective. Disassemble the computer following the steps described in Chapter 4 and replace the system board, memory module or CPU with a new one.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-11

2 Troubleshooting

2.5 2.5-inch HDD

2.5 2.5-inch HDD To check if the 2.5-inch HDD is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Message Check Procedure 2 Partition Check Procedure 3 Format Check Procedure 4 Test Program Check Procedure 5 Connector Check and Replacement Check

CAUTION: The contents of the 2.5-inch HDD will be erased when the HDD 2.5-inch HDD diagnostic test or formatting is executed. Save the required contents of the HDD to floppy disks or other storage drive in advance.

Procedure 1 Message Check When the computer's HDD does not function properly, some of the following error messages may appear on the display. Follow the steps below to check the HDD. Check 1

If either of the following messages appears, go to Procedure 2. If the following messages do not appear, perform Check 3. Insert system disk in drive Press any key when ready ..... or Non-System disk or disk error Replace and press any key

Check 2

Check TSETUP to see if the Hard Disk option has been set to “Not used”. If so, choose another setting and restart the computer. If the problem persists, go to Procedure 2.

Procedure 2 Partition Check Enter the MS-DOS system. Perform the following checks: Check 1

Type C: and press the Enter key. If you cannot change to drive C, perform Check 2. If you can change to drive C, perform Check 3.

Check 2

Type FDISK and press the Enter key. Choose “Display partition information” from the FDISK menu. If drive C is listed, perform Check 3. If drive C is not listed, return to the FDISK menu and choose the option to

2-12

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.5

2.5-inch HDD

2 Troubleshooting

create a DOS partition on drive C. Then restart the computer.. If the problem persists, go to Procedure 3.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-13

2 Troubleshooting

2.5 2.5-inch HDD

Check 3

If drive C is listed as active in the FDISK menu, perform Check 4. If drive C is not listed as active, return to the FDISK menu and choose the option to set the active partition for drive C. Then restart the computer. If the problem persists, perform Check 4.

Check 4

Enter DIR C: and press the Enter key. If the following message is displayed, go to Procedure 3. If contents of drive C are listed on the display, perform Check 5. Invalid media type reading drive C Abort, Retry, Fail?

Check 5

Use the SYS command in the MS-DOS system to install system files. If the following message appears on the display, the system files have been transferred to the HDD. Restart the computer. If the problem persists, go to Procedure 3. System transferred

NOTE: If the computer is running Windows XP Home edition and the hard disk capacity is more than 512 MB, the FDISK program will ask if you need support for a partition larger than 2 GB. Select Y for large partition support; however, be sure to read the precaution regarding access by other operating systems.

Procedure 3 Format Check The 2.5-inch HDD is formatted using the low-level format program and the MS-DOS FORMAT program. Using these programs, follow the steps below to format the HDD. Check 1

Enter FORMAT C:/S/U to format the HDD and transfer system files. If the following message appears on the display, the HDD has been formatted. Format complete If you cannot format the HDD using the test program, go to Procedure 4.

2-14

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.5

2.5-inch HDD

2 Troubleshooting

Procedure 4 Test Program Check Run the HDD test program stored on the maintenance test program disk for all test items. See Chapter 3 for details on how to use the test program. If an error is detected during the HDD test, an error code and status will be displayed. The error codes and their status names are listed in Table 2-1. If an error code is not generated and the problem still exists, go to Procedure 5. Table 2- 1 HDD error code and status

Code 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16

Status Get Parameter Fail ! Read Old Data Error Write Pattern Error Read Back Data Error Data Compare Error Restore Data Error Read Verify Error Seek Error Disk Controller Self Test Failed Disk Controller Test unexpected interrupt Failed Disk Controller action Test Failed Disk dos not support SMART Disk read attribute threshold error Disk read attribute value error Disk SMART attribute value error

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-15

2 Troubleshooting

2.5 2.5-inch HDD

Procedure 5 Connector Check and Replacement Check The HDD or system board may be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1

Make sure the following connectors have been firmly connected to the HDD, system board and CPU. HDD

System board

CPU

If any connector is loose or off, reconnect it firmly and return to Procedure 1. If there is still an error, perform Check 2. Check 2

The HDD may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4. If the problem persists, perform Check 3.

Check 3

The System board may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4. If the problem persists, perform Check 4.

Check 4

The CPU may be damaged. Replace it with a new one following the disassembling instructions in Chapter 4.

2-16

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.6 Keyboard

2 Troubleshooting

2.6 Keyboard To check if the computer’s keyboard is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check

Procedure 1 Test Program Check Execute the Keyboard test available as part of the maintenance test program. See Chapter 3 for information on how to perform the test. If an error is detected in the test, go to Procedure 2. If no error is detected, the keyboard itself is normal. Procedure 2 Connector Check and Replacement Check The keyboard or system board may be disconnected or faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1

Make sure the keyboard cable has been firmly connected to the system board.

Keyboard

System board

CPU

If the cable is loose or off, reconnect it firmly and return to Procedure 1. If there is still an error, perform Check 2. Check 2

The keyboard may be faulty. Replace it with a new one following the instructions in Chapter 4. If the problem persists, perform Check 3.

Check 3

The System board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the keyboard is still not functioning properly, perform Check 4. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 5.

Check 4

Check 5

The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-17

2 Troubleshooting

2.7 Display

2.7 Display To check if the computer’s display is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 External Monitor Check Procedure 2 Test Program Check Procedure 3 Connector Check and Replacement Check Procedure 1 External Monitor Check Connect an external monitor to the computer's external monitor port, then boot the computer. The computer automatically detects the external monitor even if resume mode is enabled. If the external monitor works correctly, the internal LCD, LCD/FL cable, or FL may be faulty. Go to Procedure 3. If the external monitor appears to have the same problem as the internal monitor, the system board may be faulty. Go to Procedure 2. Procedure 2 Test Program Check Insert the diagnostics bootable CD in the computer's CD ROM, turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If an error is detected in the test, go to Procedure 3. If no error is detected, the display itself is normal. Procedure 3 Connector Check and Replacement Check The display unit has an LCD module, Fluorescent lamp (FL), panel close switch and FL inverter board. Any of the components or their connections may be defective. Disassemble the computer following the steps described in Chapter 4, then perform the following checks: (1) If the FL does not light, perform Check 1. (2) If characters or graphics are not displayed normally, perform Check 5. (3) If the FL remains lit when the display is closed, the panel close switch may be defective. Perform Check 8. Check 1

FL

Make sure the following cables have been firmly connected to the system board and FL inverter board. FL inverter board HV cable

Check 2

2-18

System board

CPU

LCD/FL cable

If any of the cables is loose or off, reconnect it firmly and return to Procedure 3. If there is still an error, perform Check 2. The LCD/FL cable may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 3.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.7 Display

Check 3 Check 4 Check 5

2 Troubleshooting

The FL may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 4. The FL inverter board may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 5. Make sure the LCD/FL cable has been firmly connected to the system board and LCD module. FL inverter board

System board

CPU

LCD/FL cable

Check 6 Check 7 Check 8 Check 9 Check 10

If the cable is loose or off, reconnect it firmly and return to Procedure 3. If there is still an error, perform Check 6. The LCD/FL inverter cable may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 7. The LCD module may be faulty. Replace it with a new one and return to Procedure 3. If there is still an error, perform Check 8. The System board may be faulty. Replace it with a new one. If there is still an error, perform Check 9. The CPU may be faulty. Replace it with a new one following the instructions in Chapter 4. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 10.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-19

2 Troubleshooting

2.8 ODD Drive

2.8 ODD (Optical Disk Drive) To check if the internal ODD drive is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 ODD Cleaning Check Procedure 2 Test Program Check Procedure 3 Connector Check and Replacement Check

Procedure 1 ODD Cleaning Check 1. Turn off the power to the computer. 2. Open the ODD tray by inserting a slender object such as a straightened paper clip into the eject hole. The object must be long enough to activate the eject mechanism. 3. Clean the laser pickup lens with a lens cleaner. Apply the cleaner to a cloth and wipe the lens. 4. If the ODD drive still does not function properly after cleaning, go to Procedure 2. Procedure 2 Test Program Check Execute the ODD drive test program available as part of the maintenance test program. Insert the diagnostics CD in the computer's CD, turn on the computer and run the test. Then insert a test ODD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) into the ODD drive. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 3. Procedure 3 Connector Check and Replacement Check The ODD drive is connected to the system board by the connector. The connector may be disconnected from the system board or faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 Make sure the following connector has been firmly connected to the ODD drive and the system board.

ODD drive Attachment case

System board

CPU

Connector

If the connector is loose or off, reconnect it firmly and return to Procedure 2. If there is still an error, perform Check 2. Check 2 The connector may be faulty. Replace the connector with a new one following the steps in Chapter 4. If the ODD drive is still not functioning properly, perform Check 3.

2-20

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.8 ODD Drive

Check 3

Check 4

Check 5

Check 6

2 Troubleshooting

The ODD drive may be faulty. Replace the ODD drive with a new one following the steps in Chapter 4. If the ODD drive is still not functioning properly, perform Check 4. The system board may be faulty. Replace it with new one following the instructions in Chapter 4. If the ODD drive is still not functioning properly, perform Check 5. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 6. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 3.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-21

2 Troubleshooting

2.9 LAN

2.9 LAN To check if the computer’s LAN is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check

Procedure 1 Test Program Check Execute the LAN check program available as part of the maintenance test program. This program will check the LAN. Insert the Bootable CD into the CD. Turn on the computer and run the check program. See Chapter 3 for information on how to perform the check. If any abnormal is detected by the check, go to Procedure 2

Procedure 2 Connector Check and Replacement Check The LAN connector (RJ45) is mounted on the system board. If the LAN malfunctions, the system board or CPU might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 The system board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the LAN is still not functioning properly, perform Check 2. Check 2 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

2-22

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.10 SD Card/Memory Stick

2 Troubleshooting

2.10 SD/MS/MS pro/MMC/XD Card(Optional) To check if the computer’s SD/MS/MS Pro/MMC/XD Card is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check

Procedure 1 Test Program Check Execute the SD/MS/MS Pro/MMC/XD Card test program available as part of the maintenance test program. This program checks the SD/MS/MS Pro/MMC/XD card. Insert the Bootable CD into the CD. Turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 2

Procedure 2 Connector Check The Memory Card connector is mounted on the system board. If the Memory Card malfunctions, the system board or CPU might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 The system board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the Memory Card is still not functioning properly, perform Check 2. Check 2 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-23

2 Troubleshooting

2.11 Finger Print(Optional)

2.11 Finger Print(Optional) To check if the computer’s Finger Print is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check

Procedure 1 Test Program Check Execute the Finger Print test program available as part of the maintenance test program. This program checks the Finger Print. Insert the Bootable CD into the CD. Turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 2

Procedure 2 Connector Check The Finger Print connector is mounted on the system board. If the Finger Print malfunctions, the system board or Finger Print Board might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 The Finger Print board may be faulty. Replace it with a new one following the instructions in Chapter 4. Then go through procedure 1 again.If the Finger Print is still not functioning properly, perform Check 2. Check 2 The system board may be defective. Replace the system board with a new one following the steps described in Chapter 4. Then go through procedure 1 again .

2-24

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.12 3D Sensor

2 Troubleshooting

2.12 3D Sensor To check if the computer’s 3D sensor is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Replacement Check

Procedure 1 Test Program Check Execute the 3D sensor test program available as part of the maintenance test program. This program checks the3D sensor. Insert the Bootable CD into the CD. Turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 2

Procedure 2 Replacement Check The 3D sensor chipset is mounted on the system board. If the 3D sensor malfunctions, the system board might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 The system board may be faulty. Replace it with a new one following the instructions in Chapter 4. Then go through procedure 1 again .

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-25

2 Troubleshooting

2.13Parallel Port(Optional)

2.13 Parallel Port(Optional) To check if the computer’s Parallel Port is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check

Procedure 1 Test Program Check Execute the Parallel Port test program available as part of the maintenance test program. This program checks the Parallel Port. Insert the Bootable CD into the CD. Turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 2

Procedure 2 Connector Check The Parallel Port connector is mounted on the parallel board. If the Parallel Port malfunctions, the parallel board or or cable or system board or CPU might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 The parallel board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the Parallel Port is still not functioning properly, perform Check 2. Check 2 The parallel board cable may be faulty. Replace it with a new one following the instructions in Chapter 4. If the Parallel Port is still not functioning properly, perform Check 3. Check 3 The system board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the Parallel Port is still not functioning properly, perform Check 4. Check 4 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 5. Check 5 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

2-26

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.13 Audio Test

2 Troubleshooting

2.14 Audio Test To check if the computer’s Speaker is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check

Procedure 1 Test Program Check Execute the Audio test available as part of the maintenance test program. See Chapter 3 for information on how to perform the test. If an error is detected in the test, go to Procedure 2. If no error is detected, the Audio itself is normal. Procedure 2 Connector Check and Replacement Check The Audio or system board may be disconnected or faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1

Make sure the Speaker cable has been firmly connected to the system board. Speaker

System board

CPU

If the cable is loose or off, reconnect it firmly and return to Procedure 1. If there is still an error, perform Check 2. Check 2

The Speaker may be faulty. Replace it with a new one following the instructions in Chapter 4. If the problem persists, perform Check 3.

Check 3

The System board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the Audio is still not functioning properly, perform Check 4. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 5.

Check 4

Check 5

The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-27

2 Troubleshooting

2.15IEEE 1394 Test

2.15 IEEE 1394 Test To check if the computer’s IEEE 1394 is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check

Procedure 1 Test Program Check Execute the IEEE 1394 test program available as part of the maintenance test program. This program checks the IEEE 1394. Insert the Bootable CD into the CD. Turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 2

Procedure 2 Connector Check The IEEE 1394 connector is mounted on the system board. If the IEEE 1394 malfunctions, the system board or CPU might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1 The system board may be faulty. Replace it with a new one following the instructions in Chapter 4. If the IEEE 1394 is still not functioning properly, perform Check 2. Check 2 The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 3. Check 3 The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

2-28

Satellite A100/A105 / TECRA A7 Maintenance Manual

2.16Cooling Module

2 Troubleshooting

2.16 Cooling Module To check if the computer’s cooling module is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1 Test Program Check Procedure 2 Connector Check and Replacement Check

Procedure 1 Test Program Check Execute the Fan On/Off test program available as part of the maintenance test program. This test program checks the cooling module. Insert the diagnostics bootable CD in the computer's CD, turn on the computer and run the test. See Chapter 3 for information on how to perform the test. If any error is detected by the test, go to Procedure 2.

Procedure 2 Connector Check and Replacement Check The cooling module is connected to the system board. If the cooling module malfunctions, there may be a bad connection between the cooling module and the system board or either might be faulty. Disassemble the computer following the steps described in Chapter 4 and perform the following checks: Check 1

Make sure the cooling module has been firmly connected to the connector on the system board. Also make sure that the tape is not stuck to any part of the fan and that the fan is free of foreign matter.

Cooling module

Check 2

Check 3

Check 4

System board

CPU

If the connector is disconnected, connect it firmly to the system board and return to Procedure 1. If the tape is stuck to any part of the fan, stick it back to the specified point. If a foreign matter is found in the fan, remove it and then return to Procedure 1. If there is still an error, perform Check 2. The cooling module may be faulty. Replace it with a new one following the steps in Chapter 4. If the cooling module is still not functioning properly, perform Check 3. The memory may be defective. Replace the memory module with a new one following the steps described in Chapter 4. If the problem persist, perform Check 4. The CPU may be faulty. Disassemble the computer following the steps described in Chapter 4 and replace the CPU with a new one.

Satellite A100/A105 / TECRA A7 Maintenance Manual

2-29

2 Troubleshooting

2-30

2.16 Cooling Module

Satellite A100/A105 / TECRA A7 Maintenance Manual

Chapter 3 Diagnostic Programs

3 Diagnostic Programs

Chapter 3 Contents 3.1

General.......................................................................................................................... 1

3.2

Quick Start .................................................................................................................... 3

3.3

ii

3.2.1

Quick Test ............................................................................................... 3

3.2.2

Customization Test.................................................................................. 3

3.2.3

Keyboard Layout test .............................................................................. 7

3.2.4

Hotkey Test ............................................................................................. 8

3.2.5

Audio Play Test ....................................................................................... 8

3.2.6

Audio Record Test................................................................................... 8

3.2.7

DMI Read ................................................................................................ 8

3.2.8

DMI Write ............................................................................................... 9

3.2.9

3D Sensor Test ...................................................................................... 10

3.2.10

FPRD Test ............................................................................................ 16

3.2.11

FENR Test............................................................................................ 16

3.2.12

IrDA ManMaster Test ........................................................................... 16

3.2.13

IrDA ManSlave Test ............................................................................. 17

3.2.14

System Information ............................................................................... 17

3.2.15

View Logs ............................................................................................. 19

3.2.16

Exit to MS DOS .................................................................................... 19

3.2.17

The Diagnostics Screen Explanation..................................................... 19

Options........................................................................................................................ 23 3.3.1

Overview ............................................................................................... 23

3.3.2

Batch Parameters Configuration ........................................................... 24

3.3.3

Item’s Parameters Configuration........................................................... 26

3.3.4

Load Batch Parameters.......................................................................... 27

3.3.5

Save Batch Parameters .......................................................................... 28

3.3.6

LOG Parameters Setting........................................................................ 28

3.3.7

Specify LOG Viewer............................................................................. 29

3.3.8

Display LOG File .................................................................................. 30

3.3.9

LOG Viewer .......................................................................................... 30

3.3.10

LOG File Sample................................................................................... 32

Satellite A100/A105 / TECRA A7 Maintenance Manual

3 Diagnostic Programs 3.4

Subtests ....................................................................................................................... 33

3.5

System Test................................................................................................................. 36

3.6

Memory Test............................................................................................................... 40

3.7

Storage ........................................................................................................................ 46

3.8

Video........................................................................................................................... 50

3.9

Communication (COMM) .......................................................................................... 59

3.10

Peripheral .................................................................................................................... 61

3.11

Error Codes and description........................................................................................ 63

3.12

Quick Test Item List ...................................................................................................... i

Satellite A100/A105 / TECRA A7 Maintenance Manual

iii

3.1 General

3.1

3 Diagnostic Programs

General

This chapter explains the diagnostic programs which tests and diagnoses the functions of the hardware components of this computer. The diagnostic programs can be classified into two types: OPTION and DIAGNOSTIC TEST. NOTE 1: This Diagnostic supports Satellite A100/A105 / TECRA A7 NOTE 2: Before running a test, be sure to: 1. Check that all the cables are connected securely. 2. Exit the application that is currently running and close Windows. The OPTION includes the following functions: … … … … … … … … … …

Select All Items Test All Items Edit Batch Parameters Load Batch Parameters Save Batch Parameters Log Parameters Specify Log Viewer Display Error Log File DOS Shell Exit to DOS

The DIAGNOSTIC TEST Devices include the following tests: … … … … … … … … …

System Test Memory Test Storage Test Video Test Communication Test Peripheral Test Audio Test DMI Read/Write System Information

Before running the diagnostic programs, get the following tools prepared: … … … … … …

A Service Diagnostic BOOT CD A Formatted FLOPPY DISK A Test Media CD (A-BEX TEST CD-ROM TCDR-702)(for CD-ROM test) A Test Media DVD (Toshiba-EMI DVD-ROM TEST DISK TSD-1) An External Monitor (for DISPLAY test) A CD-ROM Driver (for CD-ROM test)

Satellite A100/A105 / TECRA A7 Maintenance Manual

1

3 Diagnostic Programs … … …

3.1 General

Audio Line for audio record test Loop back connector of LPT A Data CD (for CD-ROM test)

The following chapters describe all the test details. The test items could be selected from the DIAGNOSTIC TEST menu. Note: When booting up the unit for the first time, the system will automatically select the location of the result log file. If a USB floppy drive is connected, and there is an unprotected floppy diskette with more then 50KB spare space in the drive, system will save all log files into the root directory the diskette; otherwise, system will save all log files in the root directory of RAM disk.

2

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.2 Quick Start

3.2

3 Diagnostic Programs

Quick Start

When the system is booting from Service Diagnostic CD, the following screen will be displayed:

Please select a test item or select 0 to exit to MS-DOS: 3.2.1 Quick Test When this item is selected, the system will run the configured test items and generate a test report automatically. When the test is completed, a file named Quick.log would be saved in the defined location. When Quick.log is being created, meanwhile, a file named quick.log has already existed, the system will automatically rename Quick.log to Quick.old for the backup purpose of the log file. For the detail of test item, please refer to Quick Test Item List. 3.2.2 Customization Test When this item is selected, the system will run the diagnostic programs according to the procedures you defined. When the test is completed, a file named Custom.log will be saved in the defined location. Please see the following example-- Mouse test. 1.

Use arrow key to select ‘TouchPad’ item on ‘Peripheral’ in the menu, then press Space key to select it. (When it is being selected, there is a X marked in the [ ])

Satellite A100/A105 / TECRA A7 Maintenance Manual

3

3 Diagnostic Programs

3.2 Quick Start

Select ‘Test Mouse’ or press F8 to run the test. The prompt information would be displayed in the screen as below. This test item needs user to verify whether the mouse works normally.

The test result will be displayed in the following screen:

4

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.2 Quick Start

3 Diagnostic Programs

Here is another method to run the test: Highlight a test item by using arrow keys, then, press Enter to start. If there are parameters provided, user should set parameters in the parameter dialog window.

CPU Speed Test (Step by Step): 1. Select test item:

Select System—CPU—CPU Speed, then, press the Enter key.

2. Parameters Setting

Choose the OK button after you set the proper parameters in the following window.

Satellite A100/A105 / TECRA A7 Maintenance Manual

5

3 Diagnostic Programs

3.2 Quick Start

3. Test Result

System will automatically run and display the test result as follows:

Following is the comparison report of the two testing methods mentioned above: 1) Configuration and Running As to the method used in Mouse test, the user is required to select test items by pressing Space key and set the parameters artificially, (See 3.3.3 Item’s Parameters Configuration) Then press F8 to start the test. User should configure each parameter in advance; otherwise the default parameters would be used. Using this method, user is allowed to select more than one test item at one time. 2) Running the current test item As to the method adopted in CPU Speed test, user should highlight the test item and press Enter to start testing. And the user has to setup the parameters every time before running the test. Using this method, only one test item would be tested at one time.

6

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.2 Quick Start

3 Diagnostic Programs

3.2.3 Keyboard Layout test The test purpose is to check whether 18 kinds of European keyboards run well during the test procedure. When users choose the item, the names of these countries will be displayed on the screen for user choice. User press any index of token in ASCII, and the program will test the kind of keymap of the country.

The test screen would be shown as below:

It requires user to press the key and check whether the key in the screen changes color or not. User can terminate test by typing ‘END’. When testing the ‘Fn’ key, it must press the ‘Enter’ key at the same time.

Satellite A100/A105 / TECRA A7 Maintenance Manual

7

3 Diagnostic Programs

3.2 Quick Start

When the user has checked all the keys and all the keys in the screen have changed color, the diagnostics program would automatically end the test and report the pass information. If keyboard test fails, program will terminate the test and report the fail information when it is time to timeout. The test will end when all keys are pressed or test time is out after 100 seconds. 3.2.4 Hotkey Test Check whether Hotkey run well. Hotkey test mainly functional keys, for example: IE Key Audio play etc. The methods of testing hotkey are different from keyboard tests sometimes depending on the specific type of notebooks, and this explains why some types of notebooks can be tested together with keyboard while others cannot. Press E+ +N+D to quit the test. 3.2.5 Audio Play Test Check whether the system could playback audio normally. When the test is completed, a file named Audio_P.log will be saved in the defined location. 3.2.6 Audio Record Test Check whether the system could record the sound normally. If there is no error during the whole test, Pass; otherwise Fail. The test will repeat for four times. When the test is completed, a file named autest.log will be saved in the defined location. 3.2.7 DMI Read Read the information from the system’s SMBIOS and display it in the screen as follows:

8

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.2 Quick Start

3 Diagnostic Programs

User can press any key to exit the program. 3.2.8 DMI Write In addition to reading the DMI information, DMI Write also permits attributes editing and updating: Manufacture, Product Name, Version, Serial Number, and OEM Part Number, etc. The following screen will be displayed:

In this screen, there are two lines which attribute could be edited and updated. The 1st line (the font in yellow with blue background) shows the attribute’s value that is read from the current system and the 2nd line (the font in red with turquoise background) shows the same value as that in the 1st line before user’s editing. User can modify the attribute’s value in the 2nd line and press Enter to confirm the current edition and continue editing the next attribute.

Satellite A100/A105 / TECRA A7 Maintenance Manual

9

3 Diagnostic Programs

3.2 Quick Start

During the editing, user could press F2 to confirm the DMI attribute update or press F4 to ignore the modification. Press ESC to exit the program of DMI Write. The confirmation screen is as below:

The attributes that have been modified would be marked in red; otherwise in yellow. User could press F2 to save the changes, or press F4 to ignore and exit the current program. 3.2.9 3D Sensor Test In 3D Sensor test, the system checks whether the HDD protection is normal. This program judges by sampling five kinds of data shown below. No Item

Contents

1

Access platform.

An access platform is leveling.

2

Test Fixture

The Fixture which fixes PC by 90 degree inclination is used. Vibration/shock doesn't take a PCB at the time of T&D inspection.

10

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.2 Quick Start 3

Test1

3 Diagnostic Programs The display of a test program and the set method of PC are shown below. Display of a Test Program The portion which PC and Test-Fixture contact is green.

Set method of PC Z

Upper X

Judgment If all data is less than ranges, it will be OK.

Satellite A100/A105 / TECRA A7 Maintenance Manual

11

3 Diagnostic Programs 4

Test2

3.2 Quick Start

The display of a test program and the set method of PC are shown below. Display of a Test Program

Set method of PC Rear

Upper

Judgment If all data is less than ranges, it will be OK.

12

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.2 Quick Start 5

Test3

3 Diagnostic Programs The display of a test program and the set method of PC are shown below. Display of a Test Program

Set method of PC

Right

Upper

Judgment If all data is less than ranges, it will be OK.

Satellite A100/A105 / TECRA A7 Maintenance Manual

13

3 Diagnostic Programs 6

Test4

3.2 Quick Start

The display of a test program and the set method of PC are shown below. Display of a Test Program

Set method of PC Front

Upper

Judgment If all data is less than ranges, it will be OK.

14

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.2 Quick Start 7

Test5

3 Diagnostic Programs The display of a test program and the set method of PC are shown below. Display of a Test Program

Set method of PC

Left

Upper

Judgment If all data is less than ranges, it will be OK. 8

Inspection

Judgment If all data is less than ranges, it will be OK.

9

Setting When an inspection result is O.K., calibration at HPC. Calibration data If it succeeded, the system will prompt a message of PASS, otherwise the message will be FAIL.The test information will be written in log file. Note: Please do not use this program, when you test PC without 3D sensor.

Satellite A100/A105 / TECRA A7 Maintenance Manual

15

3 Diagnostic Programs

3.2 Quick Start

3.2.10 FPRD Test Both FPRD and FENR refer to finger print test, which means finger print identification system. FPRD, a self test of finger print test, detects the existence of the device. If it exists, the system will prompt a message of PASS, otherwise the message will be FAIL. 3.2.11 FENR Test In FENR test, the system scans a finger print for three times and displays Succeeded if successfully collected finger print information. Then it will scan the finger print one more time for comparison and display PASS if succeeded. If the comparison is not successful, the system will request another scan for totally five times and display FAIL if it always fails.

Note: Because, execution of this test vanishes all fingerprint data. When you perform this test, please make it only failure of a fingerprint sensor. 3.2.12 IrDA ManMaster Test This test item supports the transfer rates of 2.4Kbps, 9.6Kbps, 19.2Kbps, 38.4Kbps, 57.6Kbps, 115.2Kbps , 0.576Mbps,1.152Mbps and 4.00Mbps. The unit under testing (UUT) is called Slave, that requires a unit whose IrDA works normally(that is called Master) for transferring data between Slave and Master. Below are the operation steps: — Prepare a Master whose IrDA works normally, then run the test item from Main Menu, The master stays here to wait for slave requesting. — Prepare a slave. User should choose the test item from Main Menu and set parameters. Below is the Master Testing window:

16

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.2 Quick Start

3 Diagnostic Programs

Press any key to quit when you want to stop 3.2.13 IrDA ManSlave Test Below is the Slave Testing window.

3.2.14 System Information This function is used to read the system information. When the test is completed, a file named System.log will be saved in the defined location. During the reading process, the following screen will be displayed to indicate that the progress is in detection:

Satellite A100/A105 / TECRA A7 Maintenance Manual

17

3 Diagnostic Programs

3.2 Quick Start

On the left column of the above screen, the detected hardware components are listed. The corresponding information of the detected hardware components is displayed on the right of the screen. It displays the current running status information of the check program. The name of the program is marked on the top of the screen. At the bottom, the function keys are listed for user operation. During the detection, keyboard operation is invalid. When the detection is finished, the hardware components information will be displayed as follows:

User can use function keys listed on the bottom of the screen to display the configuration of the component or exit the current program. On the left column, the components information is listed and user can use arrow keys or PgUp/PgDn to view the list and highlight the chosen component. On the right column, the configuration information of the highlighted component is listed. Press ESC to exit this program.

18

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.2 Quick Start

3 Diagnostic Programs

3.2.15 View Logs User can enter one choice to view a log file in the screen as follows.

3.2.16 Exit to MS DOS Select this item to exit to MS DOS. 3.2.17 The Diagnostics Screen Explanation Below is an example of running a test item. It includes the following parts: Diagnostics Windows, Test Status Area, Progress Bar, Error List, Test Item’s Title, Status Bar and Message Box.

Satellite A100/A105 / TECRA A7 Maintenance Manual

19

3 Diagnostic Programs

3.2 Quick Start

1. Diagnostics Windows When a test item is running, a Diagnostics Windows is displayed in full screen. It consists of the following parts: Title Bar, Test Running Status and Report Panel, Status Bar. There would prompt a message box called USER BREAK in the central of the window whether user press ESC to interrupt the test. 2. Test Running Status and Report Panel Test Running Status and Report Panel are located on the middle of Diagnostics Windows. ‹ Test item name, test process and test result are displayed in the left; ‹ Test status and result are displayed in the upper right corner of the screen. It displays the test status of the current test item – TEST (in testing), PASS (test finished and its result is passed), FAIL (test finished and its result is failed) and SKIP (test skipped). ‹ The error list of each test module is displayed at the lower right corner of the screen. It would display the total error quantity found in the test, the most recent five error codes and description would be shown here. Detailed error report could be viewed with Logview.exe. ‹ When pressing ESC key during the test process, a User Break Windows will be popped up for the user to select. 3. USER BREAK

20

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.2 Quick Start

3 Diagnostic Programs

Pressing ESC key to interrupt the test, USER BREAK message box would be prompted out in the central of Diagnostics Window for the user to select the following actions: ‹ CONTINUE---- Continue the test; ‹ SKIP---- Stop the sub-item of current test item to go to the next item’s test; ‹ ABORT----Stop the current test item to test the next module. ‹ ABORT ALL---- Stop all the selected test items. User could use the hot key Ctrl+D to achieve the same operation. When the user calls ABORT ALL, the following message box will prompt for his selecting.

4. Title Bar: Title Bar located at the top of the window, it includes information as follows: ‹ Program Name and Its Version: Service Diagnostic Ver1.10; ‹ Test Module Name: Label the name and version of the test module. For example, in the above screen, the name of the test module is ‘Memory Tester Build Date 2002.12.31’. ‹ Status Bar: Located at the bottom of the screen as follows:

The status bar is used to indicate the current script setting and test status. It consists of two lines that includes the information as follows: ‹ Test Mode: TIMEBOUND or LOOPBOUND, e.g. LOOPBOUND in the above screen; ‹ Script File Name: Script file name, e.g. ‘Quick.INI’ in the above screen; ‹ Current Time(C. TIME): Current system time, e.g. ‘C.TIME:2004-01-04 19:21:27’ in the above screen; ‹ Test Time Remaining (LEFT): In TIMEBOUND mode, it would display the remaining test time at the same location as Current TIME (C. TIME) in the above screen; ‹ Current Loop Count: In LOOPBOUND mode, it will display the total LOOP number planning to execute and the current LOOP number have been finished, e.g. ‘COUNT: 01/01’ in the above screen;

Satellite A100/A105 / TECRA A7 Maintenance Manual

21

3 Diagnostic Programs

3.2 Quick Start

‹ CPU Temperature: Detect the temperature in the current CPU, e.g. ‘CPU: 49C’ in the above screen; ‹ Remaining Battery Capacity: Remaining Battery Capacity detected in the current Battery, e.g. ‘BAT: 97%’; ‹ Test Order: Define the test sequence. There is two sequence modes: Sequential Test Mode and Random Test Mode. The default mode is Sequential Test Mode, it would displays ‘ORDER: SEQ’ as in the above screen; ‹ LOG File Name: Display the file name of the test log, e.g. Quick.Log in the above screen; ‹ Start Test Time (S.TIME): Display the test start time for the current test item or the test script, e.g. ‘S.TIME: 2004-01-04 19:21:16’ in the above screen; ‹ Break On Error: Display ‘HALT’ as shown in the above screen when ‘Break On Error’ is enabled; ‹ Wait On Error: Display ‘WAIT’ as shown in the above screen when ‘Wait On Error’ is enabled; ‹ Pause Enable: Display ‘PAUSE’ when “Pause Enable” is enabled; ‹ Manual Interrupt Method: Display ‘Esc: Break’ to tell the user how to manually interrupt the test process.

22

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.3 Option

3.3

3 Diagnostic Programs

Options

3.3.1 Overview In Service Diagnostics, with the Options menu user can configure the batch parameters, test item’s parameters and those parameters created by the LOG file.

Options Menu Notes: • Select All/None Items

Switch between selecting all test items and selecting none. The hot key is F6. • Test Selected Items

Execute all selected test items in this editor. The hot key is F8. If “Interactive” option in batch parameters has not been selected, a warning message would be shown as below:

• Edit Batch Parameters

Satellite A100/A105 / TECRA A7 Maintenance Manual

23

3 Diagnostic Programs

3.3 Option

Configure batch parameters and all the test item’s parameters. • Load Batch Parameters

Upload all the test items and the parameters to the *.ini file. • Save Batch Parameters

Save all the parameters and the test items that are configured in the editor to a specified file. • Log Parameters

Configure LOG parameters. • Specify LOG Viewer

Specify the viewer for the LOG file. • Display Error Log File

Load the LOG file viewer specified in the Specify Log Viewer to view the LOG file. • DOS Shell

Enter the DOS Shell and execute the DOS programs. You can also exit to the Service Diagnostics Editor by the command of EXIT. • Exit to DOS

Exit the Service Diagnostics Editor and back to DOS. 3.3.2 Batch Parameters Configuration The batch parameters configuration screen can be accessed through Service Diagnostics/OPTIONS -> EDIT BATCH PARAMETERS -> BATCH PARAMETERS:

24

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.3 Option

3 Diagnostic Programs

Test Order Specify the order of the test items. Choose 'Sequence' to adopt the sequential mode; choose 'Random' to run the test items in random sequence.

Test Options Choose one of the following options:

9

Wait On Error Wait for further confirmation while an error occurs.

9

Break On Error Stop the test when a test item fails.

9

Pause Enable Pause at the end of each test items and wait for the user to response with the test items that requires the user to assist the test processes, such as the keystroke test.

9

Interactive If the item is enabled during the test, the test items that need user to response can run normally, such as Mouse test; If it is disabled, those test items will report FAIL. When the option here is enabled, it would affect all the test items while the same option in “Item Parameters Configuration” only affect that test item.

9

Monitor Battery Life Monitor the remaining battery capacity (percent).

Satellite A100/A105 / TECRA A7 Maintenance Manual

25

3 Diagnostic Programs 9

3.3 Option

Monitor CPU Thermal Monitor the CPU temperature. •

9

Test Mode

LOOPBOUND The chosen test items will run repeatedly according to the times specified in the 'Number of Loops'.

9

TIMEBOUND The chosen test items will run for an extent time specified in 'Time Limit Hrs' and 'Time Limit Min'. •

Time Limit Hrs Specify the hours whether 'TIMEBOUND' is chosen under the batch mode.

Time Limit Min Specify the minutes whether 'TIMEBOUND' is chosen under the batch mode.

Number Of Loops Specify the repeating times when 'Loop Bound' is chosen under the batch mode.

3.3.3 Item’s Parameters Configuration The test items’ parameters configuration screen can be accessed through Service Diagnostics/Options -> Edit Batch Parameters -> Item’s Parameters-> System>CPU-> Basic Functionality:

Repeat count Repeat times of the test item.

26

Interactive

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.3 Option

3 Diagnostic Programs If the item is enabled during the test, the test items that need user to response can run normally, such as PS2 Mouse test; If it is disabled, those test items will report FAIL. Whether the option here is enabled, it only affects the current test item.

Parameters For the test items with specific parameters, this option will call the related configuration screens. Otherwise, the program will show the following dialogue window:

Parameters for the specific test items: Some test items (Memory, HDD, e g...) have their individual parameters, which can be configured in their parameters setting window. 3.3.4 Load Batch Parameters Batch parameter is saved in the script file whose extension name is INI (*.INI). Below is the screen shot of “Load Batch Parameters”.

Satellite A100/A105 / TECRA A7 Maintenance Manual

27

3 Diagnostic Programs

3.3 Option

In this window, you can specify the .INI files that you wanted to be edited or modified. 3.3.5 Save Batch Parameters Here you can save the edited or modified content to the batch parameters files.

3.3.6 LOG Parameters Setting You can access the Log Parameters screen through Service Diagnostics\Options Generate Report.

28

Report Destination

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.3 Option

3 Diagnostic Programs

If selecting 'NONE', no log file will be generated; if selecting 'FILE', a log file with the name specified in 'Log File Name' will be generated. •

Log Options

9

Log Errors If selecting this parameter, errors will be recorded when the test fails.

9

Log Test Activities If selecting this parameter, the subtest results will be recorded.

9

Log Test Start Time If selecting this parameter, the start time of the test will be recorded.

9

Log Test End Time If selecting this parameter, the end time of the test will be recorded.

9

Log Errors Only If selecting this parameter, errors will be recorded only when the test fails.

9

Log Errors Only with Time If selecting this parameter, errors and time will be recorded only when the test fails.

9

Append to Old Log File If selecting this parameter, the new log will be added to the old one.

9

Log Device Info on Fail If selecting this parameter, details of the failed test will be recorded.

Log file Name Specify the Log file name. You can input the detail path of the file. System will show the detail path of the file.

3.3.7 Specify LOG Viewer You can specify the Log file viewer in the Specify Log Viewer screen.

Satellite A100/A105 / TECRA A7 Maintenance Manual

29

3 Diagnostic Programs

3.3 Option

The default viewing program of Service Diagnostics is LogView.exe. 3.3.8

Display LOG File You can specify the Log file for viewing in the Display Error Log File screen.

In this screen, you can specify a Log file and view it with the viewer designated in Specify LOG Viewer. 3.3.9 LOG Viewer Service Diagnostic Log viewer:

30

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.3 Option

3 Diagnostic Programs

↑, ↓ Scroll a line backward or forward on the screen.

Page Up, Page Down Scroll a page backward or forward on the screen.

Esc Exit the Log viewer.

F1 Display the Help information about the Log viewer operations and the functional keys.

Ctrl+Home Go to the start of the log file.

Ctrl+End Go to the end of the log file.

Ctrl+F3 Prompt the search dialogue for the user to input the string to be looked for and specify the searching method.

F3 Find the next corresponding strings given.

Satellite A100/A105 / TECRA A7 Maintenance Manual

31

3 Diagnostic Programs

3.3 Option

3.3.10 LOG File Sample Log file is a test result file, which records the following information: Test module name, Test item name, Start/End time and the test result (including PASS, FAIL, SKIP and ABORT). When a failure is found, both the error code and the error information were recorded. In the Log file, we use Test Items as the test item name, which could not be modified in the whole time. And we use the Internal Name as name in the program’s UI, which corresponds to the test item name and could be modified according to the user’s favorite. The following section is a sample of log file:

DIAG REPORT : Service Diagnostic Ver 1.00 ... Memory Tester Build Date 2004.4.12 [Walk High] Begin Time: Mon Jan 05 10:45:36 2005 Base Memory Test

: PASS

Extended Memory Test

: PASS

End Time: Mon Jan 05 10:47:51 2005 : Service Diagnostic Ver 1.00 ... Mouse Test Build Date 2005.4.12 [MSTPad] Begin Time: Mon Jan 05 10:48:54 2005 Touch Pad Test

: FAIL

ITEM TEST FAIL Function ID :502 Error Code

:50202

Error Message :Touch Pad Test Fail End Time: Mon Jan 05 10:49:16 2005

32

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.4 Subtests

3.4

3 Diagnostic Programs

Subtests

Test Group System

Sub Subtest Item ID 01 CPU

02

Memory

Board

Test ID

Test items

Internal Name

01 Basic Functionality Test

[CPUBasicFun]

02 CPU Speed Coprocessor 03 NPU Basic Functions NPU Interrupt 04 CPU Information

[CPUSpeed] Coprocessor [NPUFun] [NPUInterrupt] [CPUInformation]

05 CPU Protected Mode

[Protect]

07 MMX

[MMX]

01 DMA Controller

[DMACtrl]

02 Interval Timer

[Timer]

03 Clock / Calendar

[RealClock]

04 PCI System

[PCI]

05 Plug and Play

[PnP]

06 ACPI Test

[ACPI]

01 CPU Fan Speed Test

[FANSpeed]

03

FAN

01

BIOS ROM

[BIOSROM]

02

Parity

[Parity]

03

Pattern

04

Extended Pattern

01 Bit Stuck High Test

[BSHigh]

02 Bit Stuck Low Test

[BSLow]

03 Checker Board Test

[ChkBd]

04 CAS Line Test

[CASLine]

05 Incremental Test

[Incrment]

06 Decremental Test

[Decrment]

07 Incremental Decremental Test

[Idcrment]

01 Write/Read Cycle Test

[XWRCycle]

02 Read Cycle Test

[XRCycle]

05

Walking 1's Test

[WalkHigh]

06

Walking 0's Test

[WalkLow]

07

Memory Address

[Address]

08

Refresh Test

[Refresh]

09

Cache Memory

[CacheOne]

10

Random Memory

01 Randomize Test

[Random]

Satellite A100/A105 / TECRA A7 Maintenance Manual

33

3 Diagnostic Programs

3.4 Subtests

02 Random Increment Read/Write 11 12 Storage

01

02

Video

01

Data Bus Test Memory Speed Test HDD

ODD

Text Mode

02

640*480 VGA Mode

03

VESA Video Modes

[DataBus] [MemSpeed] 01 Sequential/Random R/W

[SeqRdRW1]

02 Sequential/Random Seek

[Seek1]

03 Performance

[Perform1]

04 Controller Check

[Controller1]

05 Diagnostic Read/Write

[DiagRW1]

06 SMART Test

[SMART1]

01 Controller Test

[CDRWController]

02 Data Transfer Rate

[CDRWTransRate]

03 Data CD Butterfly Seek

[CDRWButterfly]

04 Data CD Random Seek

[CDRWSeek]

05 Data CD Sequence Seek

[CDRWSFSeek]

06 Tray Eject Test

[CDRWTray]

01 Character Test

[CharTest]

02 Text Attribute

[Attribut]

03 Text Page Selection

[PageSel]

04 Text Color

[Color]

05 80*25 Text Mode

[Text Mode] [VGAMode]

640X480 Video Modes VESA 640x480x256 Mode 01 VESA 640x480x64K Mode VESA 640x480x32bit Mode 800X600 Video Modes VESA 800x600x256 Mode 02 VESA 800x600x64K Mode VESA 800x600x32bit Mode

03

04 05

34

[RandIncr]

[V640480_15] [V640480_16] [V640480_24] [V640480_32] [V800600_15] [V800600_16] [V800600_24] [V800600_32]

1024X768 Video Modes [V1024768_15] VESA 1024x768x256 Mode [V1024768_16] VESA 1024x768x64K Mode [V1024768_24] VESA 1024x768x32bit Mode [V1024768_32]

VESA Video Memory AGP Test

Satellite A100/A105 / TECRA A7 Maintenance Manual

[VESAMEM] [AGP]

3.4 Subtests

3 Diagnostic Programs

06

LCD Panel Test

[LCDPanel]

07

Register Test

[Register]

08

Color Purity Test

[ColPurity]

09

Direct Color Test DAC/Palette Address Bitblt Engine Test LPT

[DirectColor]

10 11 COMM

01

02 03

Peripheral

IrDA LAN Card

[DACPalAddr] [Bitblt] 01 Register Check

[LPTRegister1]

02 IRQ Check

[LPTInterrupt1]

03 External Loopback

[LPTExLoopback1]

04 ECP Mode

[LPTECP1]

01 IrDA Master

[IrMaster]

02 IrDA Slave

[IrSlave]

01 Device ID Detection

[DeviceID]

02 Vendor ID Detection

[VendorID]

03 Mac Address Detection

[MAC Address]

04

1394

01 GUID Detection

[1394 R/W Test]

01

Keyboard

01 Keyboard Data Line

[KBDataLn]

02 Keyboard Led

[KBLED]

03 Keyboard Clock Line

[KBClokLn]

01 TouchPad

[MSTpad]

02

Mouse

Satellite A100/A105 / TECRA A7 Maintenance Manual

35

3 Diagnostic Programs

3.5

3.5 System Test

System Test

Move arrow keys and press the Space key to select CPU test item from Service Diagnostic menu, then highlight CPU and press the Enter to run this test item. Subtest 01 CPU

1. Basic Functionality Test This test item is to check whether the CPU works normally through math and logic calculation, which means verifying the general registers, math registers and logic registers. 2. CPU Speed This test item is to detect the work frequency of the current CPU. User should change the parameters setting in the following window before the test:

CPU Speed Comparison--Whether you want to make a comparison of the CPU speed with the value set in ‘Expected CPU Speed’, you should choose ‘Yes’; otherwise, ‘No’.

36

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.5 System Test

3 Diagnostic Programs

Expected CPU Speed--Specify the expected CPU Speed value you want for further comparison. 3. Coprocessor 9

NPU Basic Functions Test This test item is to check whether the precision of the numeric processor in the float calculation is up to the IEEE standards.

9

NPU Interrupt Test This test item is to check whether NPU transfers the abnormal Interrupt program correctly by forcing an abnormal float. 4. CPU Information This test item is used for getting & showing CPU Information. It will be displayed as follows:

5. CPU Protected Mode Test This test item is to check whether CPU protected mode instruction works normally. 6. MMX The test item is to confirm whether the CPU supports MMX instructions. Subtest 02 Boards 1. DMA Controller

Satellite A100/A105 / TECRA A7 Maintenance Manual

37

3 Diagnostic Programs

3.5 System Test

This test item is to check whether the DMA controller works normally. 2. Interval Timer This test item is to check whether the Interval Timer (18.2Hz, 55ms) works normally. 3. Clock/Calendar This test item is to check whether the system clock/calendar works normally. 4. PCI System This test item is to check whether the bus number, device number and function number in PCI bus are valid. 5. Plug and Play This test item is to check: 1. Whether the current system supports Plug-n-Play; 2. Whether there is an ESCD (Extended System Configuration Data) in the BIOS; 3. Whether there is PCI-to-ISA bridge in the system; 4. Whether there is PCI bus in the system. 6. ACPI Test ACPI test includes two sub-items as below: System Address Map Test: Check the correctness of ACPI system memory map, and whether its mapping scope is within real memory. ACPI Table Test: Check the correctness of ACPI relative configuration tables in the current system.

Subtest 03 FAN Speed Test 1. CPU Fan Speed Test This test item is to check whether the CPU fan currently used works normally in the different speeds of stop, slow, middle and fast.

38

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.5 System Test

3 Diagnostic Programs

Satellite A100/A105 / TECRA A7 Maintenance Manual

39

3 Diagnostic Programs

3.6

3.6 Memory Test

Memory Test

This test module is to check whether the memory chip works normally. Subtest 01 BIOS ROM This test item is to check the validity of BIOS ROM that includes two sub-items -ROM Read and ROM Write Protection. ROM Read is to check whether BIOS ROM could be correctly read out, ROM Write Protect is to check whether BIOS ROM is write-protected. Subtest 02 Parity This test item is to check whether the parity checkout error could happen through writing and reading memory. Below is the parameter setting dialog window.

Test Option: Choose the Memory part to take the test– Base Memory or Extended Memory. Extended Memory Test Range: Specify the test coverage range of Extended Momory. If user chooses Total Size, it means that the whole Extended Momory will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of Extended Momory will be taken according to the coverage range that user chooses or time. Extended Memory Start Address (MB) & Extended Memory End Address (MB): Set the range of extended memory that is to be tested, the test coverage would be based on the setting and the value in ‘Percent (%) mentioned at below.

40

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.6 Memory Test

3 Diagnostic Programs

Pattern Size: Choose the pattern size – BYTE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the memory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested. Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested. Subtest 03 Patterns This test item is to check whether the system memory includes base memory and extended memory that could be accessed correctly through writing and reading with a series of designed pattern data. Below is the parameter setting dialog window.

Test Option: Choose the Memory part to take the test– Base Memory or Extended Memory. Extended Memory Test Range: Specify the test coverage range of Extended Momory. If user chooses Total Size, it means that the whole Extended Momory will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of Extended Momory will be taken according to the coverage range that user chooses or time. Extended Memory Start Address (MB) & Extended Memory End Address (MB): Set the range of extended memory that is to be tested, the test coverage would be based on the setting and the value in ‘Percent (%) mentioned at below.

Satellite A100/A105 / TECRA A7 Maintenance Manual

41

3 Diagnostic Programs

3.6 Memory Test

Pattern Size: Choose the pattern size – BYTE, WORD, DWORD or ALL. Percent (%): Choose the percentage of the defined range of the memory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested. Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested. 1. Bit Stuck High Test Data pattern: Every bit is ‘1’ (Each bit is high) 2. Bit Stuck Low Test Data pattern: Every bit is ‘0'(Each bit is low); 3. Checker Board Test Data pattern: Lo-byte and hi-byte are composed with 0101(0x5) and 1010 (0xA); 4. CAS Line Test Data pattern: Lo-byte and hi-byte are composed with 0000 (0x0) and 1111(0xF); 5. Incremental Test Data pattern: A series of increasing data from 0 by adding 1 each time; 6. Decrement Test Data Pattern: A series of decreasing data from the maximum (e.g. 0xFFFF) by subtracting 1 each time; 7. Incremental / Decrement Test Data Pattern is a series of data whose low byte is increasing data from 0x00 and high byte is decreasing data from 0xFF. Subtest 04

Extended Pattern

In addition to the above pattern test of the memory, there is Read/Write Cycle test and Read Cycle Test for the extended memory. Below is the parameter dialog window of the extended pattern test.

42

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.6 Memory Test

3 Diagnostic Programs

Test Range: Specify the test coverage range of Extended Momory. If user chooses Total Size, it means that the whole Extended Momory will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of Extended Momory will be taken according to the coverage range that user chooses or time. Extended Memory Start Address and Extended Memory End Address (MB): Set the range of extended memory that is to be tested. The test coverage will be according to the value setting in ‘Percent (%)’ mentioned at below. Percent (%): Choose the percentage of the defined range of the memory to be tested. Time Limit(h): Choose or Input the time (hour) of the defined range of the memory to be tested; Time Limit(m): Choose or Input the time (minute) of the defined range of the memory to be tested. 1. Write/Read Cycle Test Test by using both read and write instructions. 2. Read Cycle Test Test by using read instructions. Subtest 05 Walking 1’s Test The test item is to ensure that there is no short circuitry issue in memory chip. The parameter dialog window is the same as that in ‘Subtest 02 Pattern’. Subtest 06 Walking 0’s Test

Satellite A100/A105 / TECRA A7 Maintenance Manual

43

3 Diagnostic Programs

3.6 Memory Test

The test item is to ensure that there is no open circuitry issue in memory chip. The parameter dialog window is the same as that in ‘Subtest 02 Pattern’. Subtest 07 Memory Address This test item is to check short and open issue on memory address lines. Subtest 08 Refresh Test This test item is to check whether the memory refresh works normally. The parameter dialog window is as follows:

Subtest 09 Cache Memory The test item is to check whether the CPU internal cache memory could be accessed correctly. Subtest 10 Random Memory Random Memory test includes the following two test items: Randomize Test and Random Incremental Read/Write Test. The parameter dialog window is the same as that in ‘Subtest 03 Extended Pattern’. 1. Randomize Test This test item is to check whether the memory could be correctly accessed with randomized data and randomized memory address. 2. Random Increment Read/Write This test item is to check whether the memory could be correctly accessed with randomized memory address and a series of incremental data. Subtest 11 Data Bus Test This test item is to check whether the data bus works normally.

44

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.6 Memory Test

3 Diagnostic Programs

Subtest 12 Memory Speed Test This test item is to check the data-transferring rate for the cache memory and the system memory.

Satellite A100/A105 / TECRA A7 Maintenance Manual

45

3 Diagnostic Programs

3.7

3.7 Storage

Storage

Subtest 01 HDD This test item runs on IDE hard disks. It checks the functions and performance of IDE hard disk. In order to protect user’s HDD data, the password must be verified before the HDD test. The screen is as follows:

Password:hard disk 1. Sequential/Random R/W This test item is to check the HDD’s Read/Write function through data writing and reading to HDD. This test item needs user to submit the parameters:

IDE HDD Test Range-- Specify the test coverage range of IDE HDD. If user chooses Total Size, it means that the whole IDE HDD will be tested. Although user can input the parameter into other select box, but the selected result is invalid. If user chooses Special Size, the test of IDE HDD will be taken according to the coverage range that user chooses or time. LBA Start, LBA End--Specify the start and end byte in LBA (Large Block Address).

46

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.7 Storage

3 Diagnostic Programs Percent—Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested. Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested. Test Mode—Choose test mode from the following options: (1) Read & Write –Write data on the disk, then read it out and compare the two value; (2) Read Verify —Read data only; (3) Unprotected Write—Write data on the disk without backup original data. Option—Select sequential test or random test

2. Sequential/Random Seek The test item is to check the correctness of the HDD’s sector’s seeking function. This test item involves the following parameters:

IDE HDD Test Range—is same as the description of the upper item. LBA Start, LBA End-- specify start and finish byte in LBA(Large Block Address); Option-- Select sequential test or random test; Percent-- Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested;

Satellite A100/A105 / TECRA A7 Maintenance Manual

47

3 Diagnostic Programs

3.7 Storage

Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested. 3. Performance Check the HDD’s seeking speed and transfer the data rate. 4. Controller Check Check the HDD controller’s status, including HDD interrupt and unexpected interrupt. 5. Diagnostic Read/Write This test item is a quick test to verify whether the HDD could be correctly accessed and the user could specify the percentage in the below dialog.

Percent (1-100)-- Specify the coverage rate in percentage of the total disk. Time Limit(h): Choose or Input the time (hour) of the defined range of the total disk to be tested; Time Limit(m): Choose or Input the time (minute) of the defined range of the total disk to be tested; 6. SMART Test SMART stands for Self-Monitoring, Analysis and Reporting Technology. SMART test will compare the attribute values with the threshold value in the HDD’s controller to confirm whether there is any failure in the HDD Subtest 02 ODD The ODD test runs on IDE CDROM/DVD-ROM & CD-RW. It will check the ODD driver’s functionality and performance. 1. Controller Test

48

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.7 Storage

3 Diagnostic Programs

Check the CDROM controller’s status. 2. Data Transfer Rate Check the data transfer rate of the ODD drive. It will read data from the ODD disc and calculate the data transfer rate. This test needs a data CD. 3. Data CD Butterfly Seek Check the seek function of the ODD drive. It will perform a serial of seeking operations. First, locate the minimum LBA address, then the maximum, the subminimum, the sub-maximum and meet at center point. This test needs a data CD. 4. Data CD Random Seek Check the random seek function of ODD drive. Random access will reflect the performance of the heads’ random movement and seek. It tests for 1000 times. 5. Data CD Sequence Seek Check the sequential seek function of ODD drive. Perform location test to CDRW under LBA mode with the location address increasing in sequence. 6. Tray Eject Test Check the eject function of the ODD. It will eject the ODD and ask the user to confirm if the operation succeeds.

Satellite A100/A105 / TECRA A7 Maintenance Manual

49

3 Diagnostic Programs

3.8

3.8 Video

Video

This test item tests the video by: 1. 2.

displaying the figures in different graphic modes. displaying the property and color of the characters in different text modes.

User will confirm whether each video mode works normally by judging whether the display is correct. It checks whether the video memory works normally by writing data into the video memory, then reading it out and comparing the two value. Subtest 01

Text Mode

1. Character Test Tests two types of font patterns. Font 9*14 Font 9*16 It requires the user to check whether all characters of each font type displayed correctly by answering the questions prompted on screen. It will be displayed as follows:.

2. Text Attribute This test item is to check whether the text attribute of normal, hi-intensity, inverse, and blinking in VGA text mode could be correctly displayed on the screen.

50

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.8 Video

3 Diagnostic Programs It would display the below texts of the different attributes in the screen: 1. 2. 3. 4. 5. 6.

Text in normal attribute; Text in blinking normal attribute; Text in inverse attribute; Text in blinking inverse attribute; Text in hi-intensity attribute; Text in blinking hi-intensity attribute;

Users need to check whether all texts displayed correctly in the above six attributes and key in the answer ‘Y’ or ‘N’ to the prompts ‘Is this display OK? [Y/N]’. Below is the test screen of Text Attribute.

3. Text Page Selection This test item is to check whether the video memory could be correctly written and read in VGA text mode. According to the comparison of written data with read data, the program would report PASS or FAIL.

Satellite A100/A105 / TECRA A7 Maintenance Manual

51

3 Diagnostic Programs

3.8 Video

4. Text Color This test item is to check whether all 16 colors foreground and all 8 colors background works normally in VGA text mode. The bit4-6 of the attribute byte of a character defines 8 background colors (black, blue, green, cyan, red, brown, magenta, and light gray), and the bit0-3 defines 16 foreground colors (dark gray, light blue, light green, light cyan, light red, light magenta, yellow, and white besides the above 8 colors). In the test, user is required to respond according to the instruction in the screen.

5. 80 * 25 Text Mode This test item is to check whether 80*25 Text Mode works normally.

52

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.8 Video

3 Diagnostic Programs In the test, user is required to respond according to the instruction in the screen.

Subtest 02

640 * 480 VGA Mode This test item is to check whether 680*480 VGA Text mode works normally. In the test, user is required to respond according to the instruction in the screen.

Subtest 03

VESA Video Modes This test item is to check whether all the video modes supported by the video card works normally. In the test, user is required to respond following the instruction in the screen.

Satellite A100/A105 / TECRA A7 Maintenance Manual

53

3 Diagnostic Programs

3.8 Video

1. 640X480 Video Modes Test

p

2. 800X600 Video Modes Test 3.

Subtest 04

1024X768 Video Modes Test

VESA Video Memory This test item is to check whether VESA video memory could be correctly accessed (write data & read data). Below is the test item’s parameter dialog window:

54

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.8 Video

3 Diagnostic Programs

If press Ctrl+Break to force the test to terminate during execution of VESA Video Memory, the test program will not operate and display properly in further tests. Subtest 05

AGP Test This test item is to report the system’s Accelerated Graphics Port status and check whether AGP registers works normally.

Subtest 06

LCD Panel Test This test item is to check whether there is any fault in its resolution by displaying the RGB gradient color screens.

Satellite A100/A105 / TECRA A7 Maintenance Manual

55

3 Diagnostic Programs

Subtest 07

3.8 Video

Register Test This test item is to check whether the registers of the video adapter works normally.

Subtest 08

Color Purity Test This test item is to check whether the system (the video adapter and the display) could display the purity color of red, green, blue, black and white. In the test, user is required to respond according to the instruction in the screen.

Subtest 09

Direct Color Test This test item is to check the video adapter’s composing ability of direct color in high and true color mode. In the test, user is required to respond according to the instruction in the screen.

56

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.8 Video

Subtest 10

3 Diagnostic Programs

DAC/Palette Address This test item is to check the function of DAC registers and Palette registers. In the test, user is required to respond according to the instruction in the screen.

Satellite A100/A105 / TECRA A7 Maintenance Manual

57

3 Diagnostic Programs Subtest 11

3.8 Video

BitBlt Engine Test This test item is to check whether the BitBlt engine works normally. BitBlt is the abbreviation of ‘Bit Block Translate’, that means the copy of data block for 3 types, from video memory to video memory, from video memory to system memory, and from system memory to video memory. What should be done is to write the data of the type of BitBLT operation and the location of BitBLT source area and destination area into the BitBLT registers, and all those operations will be completed automatically by BitBLT engine with minimum CPU intervention.

58

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.10 Peripheral

3.9

3 Diagnostic Programs

Communication (COMM)

Subtest 01

LPT

This test item is to check whether there is open or short circuit issue in the external pins by looping back the external pins, controlling the voltage of each data pin, control pin and status pin. The test requires an external connector to insert into the tested LPT port. Below is the connector's description. Fixture Description: (9) + PD7

(15) -ERROR

(8) + PD6

(14) -AUTFD

(7) + PD5

(13)

(6) + PD4

(16) -PINIT

(5) + PD3

(1) - STROBE (10) - ACK

(4) + PD2

(12) + PE

(3) + PD1

(17) - SLIN

(2) +PD0 Note: (1)~(17) -------- Pin number

(11)+ BUSY

PD0~ PD7--------Data Line Status Line -------- –ERROR(S3), +SELECT(S4), –ACK(S6), +PE(S5), +BUSY(S7) Control Line-------- –AUTFD(C1), –PINIT(C2), -STROBE(C0), –SLIN(C3) 1. Register Check Check whether the data register and control register works normally. 2. IRQ Check Check whether LPT interrupt works normally. 3. External Loop back Check whether there is open or short circuit issue. 4. ECP Mode

Satellite A100/A105 / TECRA A7 Maintenance Manual

59

3 Diagnostic Programs

3.10 Peripheral

Check whether it supports ECP (Extended Capabilities Port) feature.

Subtest 02

LAN Card

This test item is to check whether the module can detect the existence of the network card and display its related information. 1. Device ID Detection Detect the device ID of the network card. 2. Vendor ID Detection Detect the vendor ID of the network card. 3. MAC Address Detection Detect the MAC address of the network card.

Subtest 03

1394 GUID Detection This test item is used to read and display GUID from 1394 register.

60

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.10 Peripheral

3 Diagnostic Programs

3.10 Peripheral Subtest 01

Keyboard

This test item is to check whether the keyboard works normally. 1. Keyboard Data Line Test Check whether the keyboard data line works normally. 2. Keyboard Led Test Check whether the keyboard led works normally. There are three kinds of LEDs test including: (1). Caps Lock LED, Num Lock LED and Scroll Lock LED. (2). Power LED , Battery LED , etc. (3). HDD LED.

3. Keyboard Clock Line Test Check whether the keyboard clock line works normally. Subtest 02

Mouse Test

Check whether the point devices work normally.

Satellite A100/A105 / TECRA A7 Maintenance Manual

61

3 Diagnostic Programs

3.10 Peripheral

1. Touch Pad Before test Touch Pad’s function, user should set a timeout time at below screen:

At the below screen of Touch Pad test, user can press the left button, right button, and move the mouse to verify its functions for times, and the test will end either by user break or test time is out.

62

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.11Error Codes and Description

3 Diagnostic Programs

3.11 Error Codes and description The format of ‘Error Code’ is ‘ddxxee’, and ‘dd’ is the device ID (1~2 chars), ‘xx’ is test function ID of device (2 chars), ‘ee’ is the error code of device (2 chars); the range of error code is from 01 to 99 in each device (the common error codes in all device are set to 99 and spanned). Device ddxx

Error Description Code ee Common Error 94

01xx

Cause

Interactive Mode Needed

Action

The test is not under interactive mode.

Check whether the interactive test mode is adopted.

Replace the CPU.

CPU 01

CPU General Function Error

The CPU General Function register is damaged.

02

CPU Arithmetic Error

The CPU Arithmetic Register is As above. damaged.

03

CPU Logic Error

The CPU Logic Register is damaged.

As above.

04

CPU Type Error

The CPU Type is not supportable.

Check whether the CPU is Intel CPU.

05

CPU Speed Error

The CPU speed differs from the Check the CPU speed and the set expected value. expected speed.

06

NPU General Function Error

The NPU arithmetic unit is damaged.

Replace the CPU.

07

NPU Interrupt Error

The NPU is damaged.

As above.

08

CPU Information Error

Information of the CPU cannot be acquired.

Check whether the CPU is Intel CPU.

09

Protected Instruction Error The CPU is damaged.

21

MMX Test Error

02xx

Replace the CPU.

The CPU MMX register is damaged.

Replace the CPU.

Memory 01

Read Error

The ROM BIOS has Physical problems.

Test this unit on multiple machines.

02

Write-Protect Error

The ROM BIOS has Physical problems.

As above.

03

Base Memory Error Address

The test pattern read out from the base memory is different from Test this memory chip on the one that has been written in multiple machines. this address.

Satellite A100/A105 / TECRA A7 Maintenance Manual

63

3 Diagnostic Programs

04

The test pattern read out from the extension memory is different As above. (XMS)Memory Problem from the one that has been written in this address.

05

(XMS) Out Of Range

06

Address Test Error

07

Toggle Bit Error

08

Interval Error

Wrong parameters setup.

Check and reset the parameters.

Interference between different address channels. Errors with the timer chip. The acquired refreshing frequency is out of the estimated range.

Test this memory chip on multiple machines. As above. Reset the estimated range.

09

L1 Cache test Error

The pattern read out from the L1 Cache is different from the one Test this unit on multiple that has been written in the same machines. address.

12

Data Bus Error

Interference between different data channels.

14

Speed Error

Failure during the transfer speed As above. test.

03xx

As above.

Board Repeat multiple times. Whether there is always the same error, replace the board.

DMA Test Error

DMA channel cannot transfer data normally.

04

Interval Timer Error

The difference between the actual precision of the interval timer and its theory value is out As above. of the permitted range. The timer counts imprecisely.

05

Periodic Faster Error

The frequency is beyond the standard.

As above.

06

Periodic Slower Error

The frequency is below the standard.

As above.

07

Update-ended Interrupt Error

R/W errors with the RTC refreshing interrupt controller.

As above.

08

RTC Alarm Error

The PC speaker's sound source --counter/timer 8253 cannot As above. produce corresponding timing signal.

13 14 15

PCI Bus Error No PCI. PCI Bus Scan Error PCI test fails. PCI Device Access Error PCI access fails.

16

PCI Config Verification Error

01

64

3.11Error Codes and Description

Wrong PCI configuration.

Satellite A100/A105 / TECRA A7 Maintenance Manual

Check the board. As above. As above. Check PCI configuration on main board or PCI Device configuration.

3.11Error Codes and Description

3 Diagnostic Programs

17

PCI to ISA Bridge Error

PCI-ISA bridge errors.

18 53

ESCD Error ACPI Table Test Error FAN Fan Slow Speed Test Fail Fan Stop Test Fail Fan Fast Speed Test Fail Video

ESCD errors. Errors with the ACPI table test.

Repeat multiple times. If there is always the same error, replace the board. As above. As above.

The fan slow speed test fails. The fan stop test fails. The fan fast speed test fails.

Check the FAN connection. As above. As above.

34xx 01 02 03 04xx 01 02 03 04

05

06 07

Check whether there is any Physical problems with the video physical problem with the video card. card. Text Page Selection Error As above. As above. Text Color Error As above. As above. Text Mode Error As above. As above. 1) Check whether there is any physical problem with the video 1) Physical problems with the video card. card. VGA Mode Error 2) Physical problems with the 2) Check whether there is any physical problem with the monitor. monitor. Check whether there is any Physical problems with the video Character Test Error physical problem with the video card. card. DAC/Palette Address Test As above. As above. Error Text Attribute Error

Check whether there is any Physical problems with the video physical problem with the video card or the monitor. card or the monitor.

08

Color Purity Test Error

09

VESA Mode 15bits Direct As above. Color Test Error

As above.

10

VESA Mode 16bits Direct As above. Color Test Error

As above.

11

VESA Mode 24bits Direct As above. Color Test Error

As above.

12

Get the PCX graphics map Failure in getting PCX graphics Check for the PCX graphics map. Error map.

13

Bitblt Engine Test Error

Physical problems with the video Check and see whether the video card. card has any physical problem.

14

VESA Video Memory Test Error

As above.

15

VESA VRAM Test Error

Check whether there is any Physical problems with the video physical problem with the video card or the monitor. card or the monitor.

As above.

Satellite A100/A105 / TECRA A7 Maintenance Manual

65

3 Diagnostic Programs

16

AGP Test Error

17

LCD Panel Test Error

19

Register Test Error

20

Adapter not support DDC

21

Check and see whether the AGP video card has any physical problem. Lower LCD color resolution. Replace the LCD. Physical problems with the video Check and see whether the video card. card has any physical problem. AGP configuration register errors.

The video card doesn't support DDC. The monitor doesn't support Monitor not support DDC DDC. 1) Check and see whether the video card has any physical problem. 2) Check and see whether the monitor has any physical problem.

21

8bits Text and Attribute Test Error

1) Physical problems with the video card. 2) Physical problems with the monitor.

26

8bits Video Mode Test Error

As above.

As above.

27

15bits Video Mode Test Error

As above.

As above.

28

16bits Video Mode Test Error

As above.

As above.

As above.

As above.

As above.

As above.

29 30 31xx

24bits Video Mode Test Error 32bits Video Mode Test Error Audio

01

Audio Play Fail

Cannot play music.

02

Record Fail LPT

Cannot record.

01

Data Register Error

02

Control Register Error

03

Does not Support ECP Mode(Ver3.20)

04

FIFO Test Error

05

IRQ Active Error

06

No Fixture On The Port

11xx

66

3.11Error Codes and Description

Check the Audio connection, replace the external fixture, and repeat the test. As above.

The data register can not perform Check the external fixture and normally. BIOS setup, and repeat the test. The control register can not As above. perform normally. Check the BIOS setup, and repeat LPT does not support ECP mode. the test. LPT cannot perform normally under FIF0 TEST mode (ECP As above. internal mode). 1.LPT IRQ cannot be activated. Check the external fixture and 2. The external fixture does not BIOS setup, and repeat the test. match with the chosen version. No external fixtures on LPT port. As above.

Satellite A100/A105 / TECRA A7 Maintenance Manual

3.11Error Codes and Description

09

10 11 08xx 01 02

03 09xx

3 Diagnostic Programs 1. There is OC (Open Circuit) or SC (Short Circuit) on the LPT Check the external fixture and the port CTR/STR.2. The external port pins, and repeat the test. fixture does not match with the chosen version.

CTR/STR Connection Error DTR/STR Connection Error Toshiba Fixture Error LAN Card PCI bus Error during device ID test PCI Ethernet card not present during device ID test Intel PCI Ethernet card not present during MAC test

As above.

As above.

As above.

As above.

Don’t Scan PCI

device

Don’t find Net card

Don’t support PCI BIOS Please insert Net cad

Don’t found Net Card, This Card Please update net card or use can’t be Read MAC by this other method method

Keyboard 01 03 04

05xx 01 14xx

Keyboard Map & Stroke Test Fail Clock Line Test Fail Data Line Test Fail Mouse

Keyboard Map & Stroke Test fails. Clock Line Test fails. Data Line Test fails.

Check the KBD connection and repeat the test. As above. As above.

Touch Pad Test Fail

Touch Pad Test Fail

Check the mouse connection and repeat the test.

IrDA Test 01

2400BPS Test Error

02 03 04 05 06 07 08 09

9600BPS Test Error 19200BPS Test Error 38400BPS Test Error 57600BPS Test Error 115200BPS Test Error 0.576MBPS Test Error 1.152MBPS Test Error 4.000MBPS Test Error

10

Connect time out

28xx

Failure with the infrared port or the configuration program is not executed. As above. As above. As above. As above. As above. As above. As above. As above. Failure with the infrared port or the configuration program is not executed.

Rerun the configuration program or check the infrared port. As above. As above. As above. As above. As above. As above. As above. As above. Rerun the configuration program or check the infrared port. Check the master.

1394

Can not find IEEE1394 controller

01 20xx

Don’t support 1394.

IDE-HDD 01

Get Parameter Fail !

Wrong test parameters are input Reinput the correct parameters. by user.

Satellite A100/A105 / TECRA A7 Maintenance Manual

67

3 Diagnostic Programs

02 03 04 05 06 07 09 10 11 12 13 21xx 01

Disk read attribute threshold error Disk read attribute value error Disk SMART attribute value error ODD No Disk in CDROM

HD is damaged. HD is damaged. HD is damaged. HD is damaged.

Send the HD for repair. As above. As above. As above.

The HD controller is damaged.

As above.

The HD controller is damaged.

As above.

The HD controller is damaged.

As above.

Disk dos not support SMART

Change HD which supported SMART and test again

Disk read attribute threshold error

Send the HD for repair.

Disk read attribute value error

As above.

Disk SMART attribute value error

As above.

No disk is found in the CDROM.

Insert a disk into the CD-ROM.

02

The Disk in CDROM is not Data Disk

03

IDE-CD Controller Error Functional errors with the CDROM.

Send the CD-ROM for repair.

CD Read Error

Either the disk or the CD-ROM is damaged.

Replace the disk or send the CDROM for repair.

CD Seek Error

Either the disk or the CD-ROM Replace the disk or send the CDis damaged. ROM for repair.

Eject Error

Wrong CD-ROM drive.

04 07 09

68

Write Pattern Error Data Compare Error Read Verify Error Seek Error Disk Controller Self Test Failed Disk Controller Test unexpected interrupt Failed Disk Controller action Test Failed Disk dos not support SMART

3.11Error Codes and Description

The disk in the CD-ROM is not Insert a DATA CD. Data Disk.

Satellite A100/A105 / TECRA A7 Maintenance Manual

Exit from the wrong drive.

3.12 Quick Test Item List

3 Diagnostic Programs

3.12 Quick Test Item List Device CPU

Memory

Board

FAN Video

HDD LAN Card

Test Items Basic Functionality NPU Basic Functions CPU Information BIOS ROM Cache Memory Bit Stuck High Test Bit Stuck Low Test Address Test Interval Timer Clock / Calendar ACPI Test FAN Speed 1024X768 Video Modes Test: VESA 1024x768x64K Mode VESA 1024x768x32bit Mode VESA Video Memory Color Purity Test Direct Color Test LCD Panel Sequential/Random Read SMART Check Device ID Detection Vendor ID Detection Mac Address Detection

Comment

10% or 3 minutes 10% or 3 minutes

10% or 3 minutes

25% or 3 minutes

Satellite A100/A105 / TECRA A7 Maintenance Manual

67

Chapter 4 Replacement Procedures 4

1

4 Replacement Procedures

4-ii

Satellite A100/A105 / TECRA A7 Maintenance Manual

4 Replacement Procedures

Chapter 4 Contents 4.1

General....................................................................................................................... 4-1 Safety Precautions................................................................................................ 4-2 Before You Begin ................................................................................................ 4-4 Disassembly Procedures ...................................................................................... 4-5 Assembly Procedures........................................................................................... 4-5 Tools and Equipment ........................................................................................... 4-6 Screw Tightening Torque .................................................................................... 4-6 Colors of Screw Shanks ....................................................................................... 4-7 Symbols of Screws on the Computer Body ......................................................... 4-7 Symbol examples ................................................................................................. 4-7 Removing the Battery Pack ................................................................................. 4-8 Installing the Battery Pack ................................................................................... 4-9 Removing the PCI Express Card ....................................................................... 4-10 Installing the PCI Express Card......................................................................... 4-11 Removing the Optional PC Card ....................................................................... 4-12 Installing the Optional PC Card......................................................................... 4-13 Removing the Memory Card ............................................................................. 4-14 Installing the Memory Card ............................................................................... 4-15 Removing the Optional Memory ....................................................................... 4-16 Installing the Optional Memory......................................................................... 4-18 Removing the MDC Card .................................................................................. 4-19 Installing the MDC Card.................................................................................... 4-21

4.2

HDD......................................................................................................................... 4-22 Removing the HDD ........................................................................................... 4-22 Installing the HDD............................................................................................. 4-24

4.3

Speaker Cover and Keyboard .................................................................................. 4-25 Removing the Speaker Cover and Keyboard..................................................... 4-25 Installing the Speaker Cover and Keyboard ...................................................... 4-26

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-iii

4 Replacement Procedures

4.4

Bluetooth Card ......................................................................................................... 4-27 Removing the Bluetooth Card ........................................................................... 4-27 Installing the Bluetooth Card............................................................................. 4-28

4.5

Wireless LAN Card.................................................................................................. 4-29 Removing the Wireless LAN Card .................................................................... 4-29 Installing the Wireless LAN Card ..................................................................... 4-30

4.6

ODD Bay Module .................................................................................................... 4-31 Removing the ODD Bay Module ...................................................................... 4-31 Installing the ODD Bay Module ........................................................................ 4-32 Disassembling the ODD Drive .......................................................................... 4-33 Assembling the ODD Drive............................................................................... 4-33

4.7

Display Assembly .................................................................................................... 4-34 Removing the Display Assembly....................................................................... 4-34 Installing the Display Assembly ........................................................................ 4-35

4.8

Top Cover ................................................................................................................ 4-36 Removing the Top Cover................................................................................... 4-36 Installing the Top Cover .................................................................................... 4-38

4.9

CPU Cooling Module and Fan................................................................................. 4-39 Removing the CPU Cooling Module and Fan (for VGA card Model).............. 4-39 Install the CPU Cooling Module and Fan (for VGA card Model) .................... 4-41 Removing the CPU Cooling Module and Fan ................................................... 4-42 Install the CPU Cooling Module and Fan.......................................................... 4-43

4.10

VGA Board (for VGA Board Model)...................................................................... 4-44 Removing the VGA Board................................................................................. 4-44 Installing the VGA Board .................................................................................. 4-45 Install the VGA board according to the following procedures and Figure 4-27. .. 445

4.11

CPU.......................................................................................................................... 4-46 Removing the CPU ............................................................................................ 4-46 Installing the CPU.............................................................................................. 4-47

4.12

USB board, Finger Print Board and Print Board ..................................................... 4-49 Removing the USB board, Finger Print Board and Print Board........................ 4-49

4-iv

Satellite A100/A105 / TECRA A7 Maintenance Manual

4 Replacement Procedures

Installing the USB board, Finger Print Board and Print Board ......................... 4-50 4.13

System Board, USB Board, AC-IN cable ................................................................ 4-51 Removing the System Board, USB Board, AC-IN cable .................................. 4-51 Installing the System Board, USB Board, AC-IN cable.................................... 4-52

4.14

FL Inverter Board .................................................................................................... 4-53 Removing the FL Inverter Board....................................................................... 4-53 Installing the Display Mask ............................................................................... 4-54

4.15

FL Inverter Board .................................................................................................... 4-55 Removing the FL Inverter Board....................................................................... 4-55 Installing the FL Inverter Board ........................................................................ 4-56

4.16

LCD Modules........................................................................................................... 4-57 Removing the 15.4-inch LCD module............................................................... 4-57 Installing the 15.4-inch LCD Module................................................................ 4-59

4.17

Speakers ................................................................................................................... 4-60 Removing the Speakers...................................................................................... 4-60 Installing the Speakers ....................................................................................... 4-60

4.18

Switch Cover and Switch Board .............................................................................. 4-61 Removing the Switch Cover and Switch Board ................................................ 4-61 Install the Switch Cover and Switch Board ....................................................... 4-62 Removing the Switch Cover and Switch Board ................................................ 4-63 Install the Switch Cover and Switch Board ....................................................... 4-64

4.19

Touch Pad and Button Board................................................................................... 4-65 Removing the Touch Pad and Button Board ..................................................... 4-65 Installing the Touch Pad and Button Board....................................................... 4-66 Removing the Touch Pad and Button Board ..................................................... 4-67 Installing the Touch Pad and Button Board....................................................... 4-68

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-v

4 Replacement Procedures

Figures Figure 4-1 Removing the battery pack ................................................................................. 4-8 Figure 4-2 Removing the PCI Express card ....................................................................... 4-10 Figure 4-3 Removing the PC card ...................................................................................... 4-12 Figure 4-4 Removing the memory card .............................................................................. 4-14 Figure 4-5 Removing the optional memory cover.............................................................. 4-16 Figure 4-6 Removing the optional memory........................................................................ 4-17 Figure 4-7 Removing the optional memory cover............................................................... 4-19 Figure 4-8 Removing the MDC card .................................................................................. 4-20 Figure 4-9 Removing the HDD pack cover ........................................................................ 4-22 Figure 4-10 Removing the HDD pack ................................................................................ 4-23 Figure 4-11 Removing the HDD cushion ........................................................................... 4-23 Figure 4-12 Removing the speaker cover ........................................................................... 4-25 Figure 4-13 Removing the keyboard ......................................Error! Bookmark not defined. Figure 4-14 Removing the bluetooth card .......................................................................... 4-27 Figure 4-15 Removing the wireless LAN card ................................................................... 4-29 Figure 4-16 Removing the ODD bay module..................................................................... 4-31 Figure 4-17 Removing the ODD bay module..................................................................... 4-32 Figure 4-18 Removing the bracket from ODD drive.......................................................... 4-33 Figure 4-19 Removing the screws from the back of the computer..................................... 4-34 Figure 4-20 Removing the display assembly...................................................................... 4-35 Figure 4-21 Removing the screws from the back of the computer..................................... 4-36 Figure 4-22 Removing the top cover ................................................................................. 4-37 Figure 4-23 Removing the CPU cooling module and fan................................................... 4-40 Figure 4-24 Applying silicon grease................................................................................... 4-40 Figure 4-25 Removing the CPU cooling module and fan................................................... 4-42 Figure 4-26 Applying silicon grease................................................................................... 4-43 Figure 4-27 Removing VGA board .................................................................................... 4-44 Figure 4-28 Removing the CPU ......................................................................................... 4-46 Figure 4-29 Installing the CPU........................................................................................... 4-47

4-vi

Satellite A100/A105 / TECRA A7 Maintenance Manual

4 Replacement Procedures

Figure 4-30 Securing the CPU............................................................................................. 4-48 Figure 4-31 Removing the USB board, finger print board and print board......................... 4-49 Figure 4-32 Removing the system board ............................................................................. 4-51 Figure 4-33 Removing the display mask ............................................................................ 4-53 Figure 4-34 Removing the FL inverter board ..................................................................... 4-55 Figure 4-35 Removing the 15.4-inch LCD module and screws ......................................... 4-57 Figure 4-36 Removing the 15.4-inch LCD module ............................................................ 4-58 Figure 4-37 Removing the speakers .......................................Error! Bookmark not defined. Figure 4-38 Removing the switch cover.................................Error! Bookmark not defined. Figure 4-39 Removing the switch board.................................Error! Bookmark not defined. Figure 4-40 Removing the switch board............................................................................. 4-63 Figure 4-41 Removing the touch pad and button board ..................................................... 4-65 Figure 4-42 Removing the touch pad and button board ..................................................... 4-67

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-vii

4.1 General

4.1

4 Replacement Procedures

General

This chapter explains how to disassemble the computer and replace Field Replaceable Units (FRUs). Some replacement procedures may not require you to remove all the surrounding FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they should be removed in a top-down manner, irrespective of their physical locations. The FRUs shown in the top area of the chart should normally be removed before removing the FRUs shown in the bottom area. To replace the FRUs, first identify the suspect FRU for the system failure. Next, according to this chart, determine the FRUs that need to be removed before removing the suspect FRU. After you determine those FRUs, go to the appropriate sections according to the section numbers shown in the boxes. Then start removal and replacement

How to use the chart (two examples): • For removing the System Board: First, remove the top cover with the display assembly. Then, remove the HDD, selectable bay module, Bluetooth card, keyboard, and wireless LAN card, all of which are shown above the top cover with the display assembly. • For removing the LCD Module: First, remove the display mask and FL inverter board, both of which are shown above the LCD module.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-1

4 Replacement Procedures

4.1 General

Safety Precautions Before you begin disassembly read the following safety precautions carefully. Be sure to follow them while you are working. DANGER: 1.

2.

Always use the genuine batteries or replacement batteries authorized by Toshiba. Batteries other than those differ in specifications and are incompatible with the computer. They may burst or explode. To avoid leakage of alkaline solutions, never heat or disassemble the battery packs. Never throw the battery packs into a fire. If this is violated, they will explode. The components such as the power supply and FL inverter carry high voltages. When you partially disassemble the computer and turn on the components, use extreme care not to touch the connectors and components to avoid the risk of electrical shock. Do not disassemble individual components during first-level maintenance.

WARNING: 1. To avoid the risk of electrical shock, turn the computer off and remove the AC adapter from the electrical outlet. 2. Because the battery in the computer is left charged, the risk of electrical shock remains even after the AC adapter is removed from the electrical outlet. To avoid the risk of electrical shock, be sure to remove any metal jewelry or accessories such as necklaces, bracelets, and rings before starting work. Never work with damp or wet hands. 3. To avoid personal injury, use care to avoid the sharp edges or corners of the components.

4-2

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.1 General

4 Replacement Procedures

CAUTION: 1. Before replacing a component, make sure that the replacement component meets the required specifications. To avoid computer failures, never use components that do not meet the specifications. 2. To avoid internal damage such as short circuits and fire, never drop metal objects such as screws, pins, paper clips, etc. into the components. When a screw is removed, be sure to replace a screw that is the same size as the original screw. Make sure that all the screws are fastened securely. Loose screws can cause short circuits, overheating, smoke, or fire. 3. Before raising a FRU or other component, make sure that all the component cables have been disconnected to avoid the risk of electrical shock caused by accidental contact with the energized components. 4. For AC input, be sure to use the AC adapter and AC power cable that come with your computer or Toshiba-recommended equivalents. 5. To avoid the risk of electrical shock, make sure that all the replacement components meet the specifications of the computer and that all the cables and connectors are fastened securely. 6. Inside the PC are components that become hot during operation (such as the CPU and cooling module). To avoid burns, let the hot components cool down before starting inspection or repair task.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-3

4 Replacement Procedures

4.1 General

Before You Begin Before you begin to disassemble the computer, keep in mind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack. Remove the optional parts and accessories as well. The procedures for removing the batteries will be explained later. Disassemble the computer only when an abnormality has occurred. Use only the recommended tools. To run and store the computer, be sure to prepare a working environment that is free from: ‰ Dust and contaminants ‰ Static electricity ‰ Extremely high or low temperatures and extremely high humidity

Run the diagnostic tests explained in Chapter 2 of this manual to identify the FRU that has probably caused the system failure. Perform only the required machine operations. Use only the disassembly and reinstallation procedures described in this manual. Place the removed components in a safe place away from the computer so that they are not damaged or get in the way of you doing your work. Normally, a number of screws need to be removed or replaced during disassembling. Place the removed screws in a safe place so that you can easily find the right screws for the right components. When assembling the computer, use the specified screws to fasten the parts to the specified locations. See the appropriate explanations and figures for screw sizes. To avoid personal injury, use care to handle components that have sharp edges or corners. After you have replaced a FRU, check that the FRU works correctly to ensure normal computer operation.

4-4

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.1 General

4 Replacement Procedures

Disassembly Procedures The cable connectors come in these two basic types: ‰ Pressure plate connectors ‰ Normal pin connectors

To remove a pressure plate connector, pull up the tabs on either side of the connector's plastic pressure plate and gently pull the cable out of the connector. To reconnect the cable to the pressure plate's connector, raise the pressure plate up to a satisfactory height and slide the cable into the connector. Secure the cable in the correct position by pressing down the sides of the pressure plate so that the plate is flush with the sides of the connector. Grasp and pull the cable gently to check that the cable is connected firmly. If the cable came off the connector, reinsert the cable by raising the pressure plate up to a satisfactory height. Normal pin connectors are used for all the other types of cables. These connectors can be installed or removed by simply inserting them or pulling them out.

Assembly Procedures You have to reassemble the computer after you have disassembled the computer and fixed the component that caused the problem. When reassembling the computer, keep the following general guidelines in mind: ‰ Take your time to carry out the suggested instructions completely. Hurried reassembly can often cause problems. ‰ Check that all the cable and connectors are fastened securely. ‰ Before securing the FRUs or other parts, check that the cables are not caught by the screws or FRUs. ‰ Check that all the latches are closed securely. ‰ Check that all the required screws are used to secure the FRUs. Using wrong screws can damage the threads or heads of the screws or does not ensure that the FRUs are secure.

After installing a FRU, make sure that the FRU and computer work normally.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-5

4 Replacement Procedures

4.1 General

Tools and Equipment For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipment. The proper use of this equipment will ensure successful repair work and reduce the costs for repairing damaged components. The equipment and tools required for disassembly and reassembly are: ‰ ‰ ‰ ‰ ‰ ‰ ‰ ‰ ‰

One 2 mm Phillips screwdriver One 4 mm flat-blade screwdriver Torx screwdriver Tweezers (for pulling out screws) ESD mats (for the floor and work desks) An ESD wrist strap or heel grounder Anti-static carpets or flooring Air ionizers (for highly electrostatic sensitive areas) A plastic card (in credit card size)

Screw Tightening Torque To secure screws, follow the torque values listed below. Over tightening can damage components and screws. Under tightening can loosen the screw or cause screws to come off, which may result in short circuits or other damage. ‰ M2 (2 mm)

0.22 N・m (2.2 kgf・cm)

‰ M2.5 (2.5 mm)

0.36 N・m (3.5 kgf・cm)

‰ M3 (3 mm)

0.51 N・m (5.0 kgf・cm)

‰ M2.5x4 PSP TITE screws

0.204 N・m (2.0 kgf・cm)

‰ M2.5x6 GIZA TITE screws 0.36 N・m (3.5 kgf・cm)

4-6

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.1 General

4 Replacement Procedures

Colors of Screw Shanks For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows: ‰ Screws of an even-numbered length Brown ‰ Screws of an odd-numbered length White ‰ Screws of a special length Black Screws of a special length are those of a length having decimal places, such as 2.5 mm and 2.6 mm.

Symbols of Screws on the Computer Body For easy maintenance, the screw types are shown on the computer body as symbols. A symbol consists of a letter representing the screw type and a numeral representing the screw length. ‰ ‰ ‰ ‰ ‰ ‰

Screw type Bind screw Flat-head screw Super flat-head screw Tapping screw Other screws

Letter B (stands for bind) F (stands for flat-head) S (stands for super flat-head) T (stands for tapping) U (stands for unique-pan head screws, studs, etc.)

Symbol examples ‰ 6 mm bind screw B6 ‰ 12 mm bind screw B12 ‰ 5 mm stud U5 (The numeral represents the rounded length of the threaded portion irrespective of the entire stud length.)

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-7

4 Replacement Procedures

4.1 General

Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4-1. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up their casing. 1. Turn the computer upside down so that the back is facing you. 2. Slide out the battery lock. 3. Slide the battery release latch and remove the battery pack from the computer.

Figure 4-1 Removing the battery pack

NOTE: Dispose of the used battery packs as required by local ordinances or regulations.

4-8

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.1 General

4 Replacement Procedures

Installing the Battery Pack Install the battery pack according to the following procedures and Figures 4-1. CAUTION: The battery packs contain a lithium ion battery, which can explode due to improper replacement, use, handling, or disposal. Always dispose of the battery packs as required by local ordinances or regulations. Use only replacement batteries recommended by Toshiba.

NOTE: Visually check the battery's terminals. If they are dirty, clean them with a dry cloth. 1. Gently insert a new or recharged battery pack into place. Check that the battery release latch slides in and stops with a click. 2. Slide in the battery lock.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-9

4 Replacement Procedures

4.1 General

Removing the PCI Express Card Remove the PCI express card according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode. 1. Push the eject button for the PCI express card to be removed until it stops and release the button. 2. When the eject button pops out slightly, push it again. 3. When the PCI express card pops out, grasp it and pull it out.

Figure 4-2 Removing the PCI express card

4-10

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.1 General

4 Replacement Procedures

Installing the PCI Express Card Install the optional PCI express card according to the following procedures and Figure 4-2, after checking that the computer is turned off in boot mode. 1. Insert the PCI express card gently until it stops and is seated securely. 2. Check that the PCI express card is seated securely. After the PCI express card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card is compatible with the current hardware configuration.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-11

4 Replacement Procedures

4.1 General

Removing the Optional PC Card Remove the optional PC card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. CAUTION: Install or remove the PC card correctly, according the manuals for the PC card and the operating system you are using. 1. Push the eject button for the PC card to be removed until it stops then release the button. 2. When the eject button pops out slightly, push it again. 3. When the PC card pops out, grasp it and pull it out.

Figure 4-3 Removing the PC card

4-12

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.1 General

4 Replacement Procedures

Installing the Optional PC Card Install the optional PC card according to the following procedures and Figure 4-3, after checking that the computer is turned off in boot mode. 1. Insert the PC card gently until it stops and is seated securely. 2. After checking that the PC card is seated securely, push the PC card release lever slightly. After the PC card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card is compatible with the current hardware configuration.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-13

4 Replacement Procedures

4.1 General

Removing the Memory Card Remove the memory card according to the following procedures and Figure 4-4, after checking that the computer is turned off in boot mode. 1. Open the card cover. 2. Push the memory card to be removed until it stops then release the memory card. 3. When the memory card pops out, grasp it and pull it out.

Figure 4-4 Removing the memory card

4-14

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.1 General

4 Replacement Procedures

Installing the Memory Card Install the memory card according to the following procedures and Figure 4-4, after checking that the computer is turned off in boot mode. 1. Insert the memory card gently until it stops and is seated securely. 2. Check that the memory card is seated securely. After the PC card is installed, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the PC card is compatible with the current hardware configuration.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-15

4 Replacement Procedures

4.1 General

Removing the Optional Memory Remove the optional memory (module) according to the following procedures and Figures 45 and 4-6, after checking that the computer is turned off in boot mode. CAUTION: Remove the optional memory after turning off the computer. If this is violated, the computer or memory can be damaged. 1. Turn the computer upside down. 2. Release one optional memory cover securing the screw. 3. Remove the memory cover. CAUTION: Do not touch the connectors on the memory modules or in the computer. Contaminated connectors can cause memory access problems.

Figure 4-5 Removing the optional memory cover

4-16

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.1 General

4 Replacement Procedures

4. Spread out the two memory lock stoppers so that the memory module pops up. 5. Pull the memory module up and out at an angle, using care to avoid touching the connectors.

Figure 4-6 Removing the optional memory

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-17

4 Replacement Procedures

4.1 General

Installing the Optional Memory Install the optional memory (module) according to the following procedures and Figures 4-5 and 4-6, after checking that the computer is turned off in boot mode. CAUTION: Install the optional memory after turning off the computer. If this is violated, the computer or memory can be damaged. 1. Insert the memory module into the connector at an angle of 45 degrees. 2. Press down on the memory module so that it is secured with both memory lock stoppers. 3. Reinstall the optional memory cover. 4. Secure the optional memory cover with the optional memory cover securing screw. After the computer is turned on, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the installed memory module has been recognized by the system. If it has not been recognized yet, check the connections. CAUTION: To prevent system malfunctions, always use Slot A first to insert the memory modules.

4-18

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.1 General

4 Replacement Procedures

Removing the MDC Card Remove the MDC Card (Modem Daughter Card) according to the following procedures and Figures 4-7 and 4-8, after checking that the computer is turned off in boot mode. CAUTION: Remove the MDC card after turning off the computer. If this is violated, the computer or MDC card can be damaged. 1. Turn the computer upside down. 2. Release the optional memory cover securing screw. 3. Remove the optional memory cover. CAUTION: Do not touch the connectors on the MDC card or in the computer. Contaminated connectors can cause MDC card failures.

Figure 4-7 Removing the optional memory cover

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-19

4 Replacement Procedures

4.1 General

4. Remove the two M2x3 white bind screws securing the MDC card. 5. Lift the MDC card and disconnect it from CN506 on the system board. 6. Disconnect the MDC cable from connector JP1 on the MDC card.

Figure 4-8 Removing the MDC card

4-20

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.1 General

4 Replacement Procedures

Installing the MDC Card Install the MDC card according to the following procedures and Figures 4-7 and 4-8, after checking that the computer is turned off in boot mode. CAUTION: Install the MDC card after turning off the computer. If this is violated, the computer or MDC card can be damaged.

CAUTION: Do not touch the connectors on the MDC card or in the computer. Contaminated connectors can cause MDC card failures. 1. Connect the MDC cable to connector JP1 on the MDC card. 2. Connect the MDC card to CN506 on the system board. 3. Secure the MDC card with two M2x3 white bind screws. 4. Install the optional memory cover. 5. Secure the optional memory cover by tightening the securing screw. After the computer is turned on, check the hardware configuration in the Hardware Setup or TSETUP program to make sure that the installed MDC card has been recognized by the system. If it has not been recognized yet, check the connections.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-21

4 Replacement Procedures

4.2

4.2 HDD

HDD

Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive.

Remove the HDD (hard disk drive) according to the following procedures and Figures 4-9, 410 and 4-11. 1. Release the HDD cover screw securing the HDD cover. 2. Remove the HDD cover.

Figure 4-9 Removing the HDD pack cover

4-22

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.2 HDD

4 Replacement Procedures

3. Remove the HDD pack by pulling on the cushion attached to the pack, following the direction of the arrows.

Figure 4-10 Removing the HDD pack NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or replace the HDD pack only if it fails. 4. Place the HDD pack on a flat surface (such as a desk), and remove the two cushions.

Figure 4-11 Removing the HDD cushion CAUTION: Do not apply pressure to the top or bottom of the drive.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-23

4 Replacement Procedures

4.2 HDD

Installing the HDD Install the HDD according to the following procedures and Figures 4-9, 4-10 and 4-11. CAUTION: To avoid damage, always hold the HDD only by its sides. 1. Attach the HDD cushion to the HDD pack. CAUTION: To prevent the HDD bracket from being distorted when installing the HDD pack into the computer, do not press the center of the HDD pack. Always hold the HDD pack by its sides. 2. Install the HDD pack into the correct position in the computer. Connect the HDD pack to the computer, holding the HDD pack by its sides. 3. Insert the HDD pack. 4. Secure the HDD cover by tightening the HDD cover screw.

4-24

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.3 Speaker over and Keyboard

4.3

4 Replacement Procedures

Speaker Cover and Keyboard

Removing the Speaker Cover and Keyboard Remove the Speaker Cover and Keyboard according to the following procedures and Figures 4-12, 4-13. 1. Release the following 10 latches on the switch cover, in that order: - Six bottom latches - Four front latches 2. Remove the speaker cover.

Figure 4-12 Removing the speaker cover

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-25

4 Replacement Procedures

4.3 Speaker over and Keyboard

3. Remove two M2.5x2.6 black bind securing screws. 4. Disconnect the keyboard cable from CN11 on the system board.

Figure 4-13 Removing the keyboard

Installing the Speaker Cover and Keyboard Install the speaker cover and keyboard according to the following procedures and Figures 412, 4-13. 1. Connect the keyboard cable to CN11 on the system board. 2. Secure the keyboard with two M2.5x2.6 black bind screws. 3. Place the speaker cover in the correct position and secure the following 10 latches, in that order: - Six bottom latches - Four front latches 4. Close the display and turn the computer over.

4-26

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.4 Bluetooth Card

4.4

4 Replacement Procedures

Bluetooth Card

Removing the Bluetooth Card Remove the Bluetooth card according to the following procedures and Figure 4-14. 1. Disconnect the antenna cable with tweezers. 2. Disconnect the Bluetooth SUMI-card connector CN9 on the system board. 3. Remove two M2x3 white bind screws. 4. Remove the Bluetooth card.

Figure 4-14 Removing Bluetooth card

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-27

4 Replacement Procedures

4.4 Bluetooth Card

Installing the Bluetooth Card Install the Bluetooth card according to the following procedures and Figure 4-14. 1. Connect the Bluetooth SUMI-card to CN9 on the system board and secure the Bluetooth card with two M2x3 white flat-head screws. 2. Connect the antenna cable by pressing it firmly into place.

4-28

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.5 Wireless LAN Card

4.5

4 Replacement Procedures

Wireless LAN Card

Removing the Wireless LAN Card Remove the wireless LAN card according to the following procedures and Figure 4-15.

CAUTION: Do not touch the connectors on the wireless LAN card and in the computer with your bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural oils, etc. from your hands. 1. Disconnect the two antenna cables with tweezers. 2. Spread out stoppers securing the wireless LAN card until the card pops up. 3. Pull the wireless LAN card up and out at an angle.

Figure 4-15 Removing the wireless LAN card

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-29

4 Replacement Procedures

4.5 Wireless LAN Card

Installing the Wireless LAN Card Install the wireless LAN card according to the following procedures and Figure 4-15. 1. Insert the wireless LAN card into the connector at angle of 45 degrees. 2. Press down on the wireless LAN card to secure it with the stoppers. 3. Connect the two antenna cables by pressing them firmly into place. CAUTION: Do not touch the connectors on the wireless LAN card and in the computer with your bare hands. Wireless LAN cards can fail if they are contaminated with sweat, natural oils, etc. from your hands.

4-30

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.6 ODD Bay Module

4.6

4 Replacement Procedures

ODD Bay Module

Removing the ODD Bay Module NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules. Remove the ODD bay module according to the following procedures and Figures 4-16, 4-17. 1. Turn the computer upside down. 2. Remove the M2x4 black flat-head screw. 3. Turn the computer over and open the display. 4. Push out on the ODD bay module in the direction of the arrow. CAUTION: Handle the ODD bay module carefully it can become hot during operation.

Figure 4-16 Removing the ODD bay module

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-31

4 Replacement Procedures

4.6 ODD Bay Module

Figure 4-17 Removing the ODD bay module

Installing the ODD Bay Module Install the ODD bay module according to the following procedures and Figures 4-16, 4-17. 1. Place the ODD bay module in the correct position and slide it in. 2. Push it in until it clicks into place. 3. Close the display and turn the computer over. 4. Secure the ODD bay module with one M2x4 black flat-head screw.

4-32

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.6 ODD Bay Module

4 Replacement Procedures

Disassembling the ODD Drive NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails. Disassemble the ODD drive according to the following procedures and Figure 4-18. 1. Remove two M2x3 white flat-head screws. 2. Remove the bracket.

Figure 4-18 Removing the bracket from the ODD drive

Assembling the ODD Drive Assemble the ODD drive according to the following procedures and Figure 4-18. 1. Seat the bracket and secure it with two M2x3 white flat-head screws.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-33

4 Replacement Procedures

4.7

4.7 Display Assembly

Display Assembly

Removing the Display Assembly CAUTION: Use care to avoid that the antenna cable is caught between the display assembly and computer. Remove the display assembly according to the following procedures and Figures 4-19, 4-20. 1. Turn the computer so the back is facing you and remove two M2.5x5 black flat-head screws. 2. Restore the normal computer placement and open the display panel.

Figure 4-19 Removing the screws from the back of the computer 3. Disconnect the LCD/FL cable from CN3 on the system board. 4. Remove four M2.5x5 black flat-head screws securing the LCD module to the top cover. 5. Remove the wireless antenna cables from the top cover. 6. Remove the display module.

4-34

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.7 Display Assembly

4 Replacement Procedures

Figure 4-20 Removing the display assembly

Installing the Display Assembly Install the display assembly according to the following procedures and Figures 4-19, 4-20. 1. Place the display panel in the correct position and push the wireless antenna cable into the top cover. 2. Connect the LCD/FL cable to CN3 on the system board. 3. Secure the display assembly with four M2.5x5 black flat-head screws. 4. Close the display panel and turn the computer so the back is facing you and secure it with two M2.5x5 black flat-head screws.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-35

4 Replacement Procedures

4.8

4.8 Top Cover

Top Cover

Removing the Top Cover Remove the top cover according to the following procedures and Figures 4-21 and 4-22. 1. Turn the computer upside down and remove the following 17 screws: - Fifteen M2.5x6 black bind screws - Two M2.5x4 black flat-head screws

Figure 4-22 Removing the screws from the bottom of the computer 2. Turn the computer right side up.

4-36

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.8 Top Cover

4 Replacement Procedures

1. Disconnect the switch board flat cable from CN14. 2. Disconnect the touch pad board flat cable from CN15. 3. Disconnect the touch pad flat cable from CN12. 4. Disconnect the speakers L and R cable from CN5 and CN8. 5. Release the following 11 latches on the switch cover, in that order: - Three bottom latches - Three Left latches - Four right latches - One front latch 6. Lift up the top cover.

Figure 4-23 Removing the top cover

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-37

4 Replacement Procedures

4.8 Top Cover

Installing the Top Cover Install the top cover with the display assembly according to the following procedures and Figures 4-21, 4-22. 1. Seat the top cover, adjusting its position. 2. Secure the following 11 latches on the top cover, in that order: - Three bottom latches - Three Left latches - Four right latches - One front latch 3. Connect the switch board, touch pad, touch pad board flat cables and speaker L and R cable to CN14, CN15, CN12, CN5 and CN8 on the system board. 4. Turn the computer upside down and secure it with the following 17 screws: - Fifteen M2.5x6 black bind screws - Two M2.5x4 black flat-head screws

4-38

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.9 CPU Cooling Module and Fan

4.9

4 Replacement Procedures

CPU Cooling Module and Fan

CAUTION: When removing the cooling module, keep the following in mind: The cooling module can become very hot during operation. Be sure to let it cool down before starting the repair work. Do not touch or cause shock to the fan in the cooling module.

NOTE: The screws for Steps 5 cannot be removed, only loosened. Removing the CPU Cooling Module and Fan (for VGA card Model) Remove the CPU cooling module and fan according to the following procedures and Figures 4-23, 4-24. 1. Disconnect the fan cable from CN13. 2. Remove the two M2.5x6 black bind screws securing the fan. 3. Remove two M2x4 white flat-head screws on the CPU cooling module using the indicated numbered order. 4. Remove the CPU bracket. 5. Release the four screws on the VGA cooling module using the indicated numbered order. 6. Remove the CPU cooling module and fan.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-39

4 Replacement Procedures

4.9 CPU Cooling Module and Fan

Figure 4-23 Removing the CPU cooling module and fan

Figure 4-24 Applying silicon grease

4-40

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.9 CPU Cooling Module and Fan

4 Replacement Procedures

Install the CPU Cooling Module and Fan (for VGA card Model) Install the cooling Module according to the following procedures and Figures 4-23, 4-24. CAUTION: When installing the cooling module, keep the following in mind: 1. Be sure to confirm the correct position for the module. 2.

Secure the relevant screws on the main board according to the number sequence sealed on heat sink module.

NOTE: Apply silicon grease with a special syringe to cover the surface of the CPU chip completely. 1. If silicon grease is already applied to the CPU and fan module, wipe them off with a cloth. By using a special syringe, apply silicon grease to the CPU and VGA chip center so that the entire CPU chip is covered with the grease. 2. Install the CPU cooling module and fan into the correct position in the computer. 3. Connect the fan cable to CN13 on the system board 4. Secure the fan with two M2.5x6 black bind screws. 5. Secure the VGA cooling module with four screws using the indicated numbered order. 6. Place the CPU cooling module and bracket in the correct position and secure them with the two M2x4 white flat-head screws.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-41

4 Replacement Procedures

4.9 CPU Cooling Module and Fan

Removing the CPU Cooling Module and Fan CAUTION: When removing the cooling module, keep the following in mind: The cooling module can become very hot during operation. Be sure to let it cool down before starting the repair work. Do not touch or cause damage to the fan in the cooling module.

Remove the CPU cooling module and fan according to the following procedures and Figures 4-25, 4-26. 1. Disconnect the fan cable from CN13. 2. Remove two M2.5x6 black bind screws securing the fan. 3. Remove the two M2x4 white flat-head screws securing the CPU cooling module using the indicated numbered order. 4. Remove the CPU bracket. 5. Remove the CPU cooling module and fan.

Figure 4-25 Removing the CPU cooling module and fan

4-42

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.9 CPU Cooling Module and Fan

4 Replacement Procedures

Figure 4-26 Applying silicon grease Install the CPU Cooling Module and Fan Install the cooling Module according to the following procedures and Figures 4-25, 4-26. CAUTION: When installing the cooling module, keep the following in mind: 1. Be sure to confirm the correct position for the module. 2. Secure the relevant screws on the main board according to the number sequence sealed on heat sink module.

NOTE: Apply silicon grease with a special syringe to cover the surface of the CPU chip completely. 1. If silicon grease is already applied to the CPU and fan module, wipe it off with a cloth. By using a special syringe, apply silicon greases to the CPU chip center so that the entire CPU chip is covered with the greases. 2. Install the CPU cooling module and fan into the correct position in the computer. 3. Connect the fan cable to CN13 on the system board 4. Secure two M2.5x6 black bind screws on the fan. 5. Seat the CPU cooling module and bracket in the correct position and secure them with two M2x4 white flat-head screws.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-43

4 Replacement Procedures

4.10 VGA Board (for VGA Board Model)

4.10 VGA Board (for VGA Board Model) Removing the VGA Board Remove the VGA board according to the following procedures and Figures 4-27. 1. Remove two M2x4 white flat-head screws. 2. Remove the VGA board.

Figure 4-27 Removing the VGA board

4-44

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.10 VGA Board (for VGA Board Model)

4 Replacement Procedures

Installing the VGA Board Install the VGA board according to the following procedures and Figure 4-27. 1. Seat the VGA board to the corrector. 2. Secure the VGA board with two M2x4 white flat-head screws.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-45

4 Replacement Procedures

4.11 CPU

4.11 CPU Removing the CPU CAUTION: When removing the CPU, keep the following in mind: The CPU can become very hot during operation. Be sure to let it cool down before starting repair work. Remove the CPU according to the following procedures and Figures 4-28, 4-29 and 4-30. NOTE: FOXCONN CPU socket will be 180 degrees to the right. 1. Unlock the CPU by rotating the cam on the CPU socket 120 degrees to the left with a flat-blade screwdriver (in the order shown in the figure below). 2. Remove the CPU.

Figure4-28 Removing the CPU

4-46

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.11 CPU

4 Replacement Procedures

Installing the CPU Install the CPU according to the following procedures and Figures 4-29, 4-30. 1. Check that the triangle on the cam is in the unlock position. 2. Attach the CPU to the correct position in the CPU socket. Align the CPU with the CPU socket by using the triangle as a guide.

Figure 4-29 Installing the CPU

CAUTION: Seat the CPU by aligning the triangle with the shaded area.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-47

4 Replacement Procedures

4.11 CPU

3. Secure the CPU by rotating the cam 120 degrees to the right with a flat-blade screwdriver. NOTE: FOXCONN CPU socket will be 180 degrees to the left.

Figure 4-30 Securing the CPU

4-48

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.12 System Board, USB board, AC-IN cable

4 Replacement Procedures

4.12 USB board, Finger Print Board and Print Board Removing the USB board, Finger Print Board and Print Board Remove the USB board, finger print board and print board according to the following procedures and Figures 4-31. 1. Remove USB SUMI-card from CN26 on the system board. 2. Remove the USB board from base enclosure. 3. Remove USB SUMI-card from CN3000 on the USB board. 4. Remove finger Print SUMI-card from CN23 on the system board. 5. Remove the finger print board from base enclosure. 6. Remove finger Print SUMI-card from CN6052 on the finger print board. 7. Remove one M2.5x3 flat-round-head screw securing the print board. 8. Remove print SUMI-card from CN5000 on the print board. 9. Remove the print board from base enclosure.

Figure 4-31 Removing the USB board, finger print board and print board

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-49

4 Replacement Procedures

4.12 System Board, USB board, AC-IN cable

Installing the USB board, Finger Print Board and Print Board Install the USB board, finger print board and print board according to the following procedures and Figure 4-31. Note: Be careful of the kill switch button for the USB board. It can be damaged when installing the USB board. Make sure it is in the correct position. 1. Seat the print board in the correct position and connect the print SUMI-card to CN5000 on the print board. 2. Secure the print board with one M2.5x3 flat-round-head screw. 3. Connect the finger print SUMI-card to CN6052 on the USB board. 4. Seat the finger print board in the correct position and connect the finger print SUMIcard to CN23 on the print board. 5. Connect the USB SUMI-card to CN3000 on the USB board. 6. Seat the USB board in the correct position and connect the USB SUMI-card to CN26 on the system board. 7. Be sure the kill switch button is operational before proceeding.

4-50

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.13 Display Mask

4 Replacement Procedures

4.13 System Board, USB Board, AC-IN cable Removing the System Board, USB Board, AC-IN cable NOTE: Be careful of the eject button for the PC card. It can be damaged when removing the board. Make sure it is securely installed. Remove the System Board, USB Board, AC-IN cable according to the following procedures and Figures 4-32. 1. Remove MIC from CN28 on the system board. 2. Remove one M2x4 black flat-head screw. 3. Remove the RJ11 cable from CN50 on the system board and then remove the system board.

Figure 4-32 Removing the system board 4. Turn the system board upside down. 5. Remove the AC-IN cable from CN503.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-51

4 Replacement Procedures

4.13 Display Mask

Installing the System Board, USB Board, AC-IN cable Install the System Board, USB Board, AC-IN cable according to the following procedures and Figure 4-32. NOTE: Be careful of the eject button for the PC card. It can be damaged when installing the system board. Make sure it is pushed in. 1. Turn the system board upside down and connect the AC-IN cable to CN503. 2. Turn the system board over and connect the RJ11 cable to CN50 on the system board. 3. Seat the system board in the correct position. 4. Secure the system board with one M2x4 black flat-head screw. 5. Seat the MIC in the correct position and connect the MIC cable to CN28 on the system board.

4-52

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.14 FL Inverter Board

4 Replacement Procedures

4.14 FL Inverter Board Removing the FL Inverter Board Remove the FL inverter board according to the following procedures and Figure 4-33. 1. Remove one M2.5x4.5 white flat-head screw.

Figure 4-33 Removing the FL inverter board 2. Lift the LCD module, FL inverter board and disconnect the LCD/FL cable from the LCD/FL connector. 3. Disconnect the HV cable from the HV connector and remove the FL inverter board.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-53

4 Replacement Procedures

4.14 FL Inverter Board

Installing the Display Mask Install the display mask according to the following procedures and Figure 4-33. 1. Seat the display mask in the correct position and secure the following 27 latches, in that order: - Six top latches - Five latches on each of the left and right sides - Eleven bottom latches 2. Secure the display mask with the following 5 screws, in that order: - Three M2.5x4.5 white flat-head screws on the top - Two M2.5x4.5 white flat-head screws on bottom 3. Secure the following 5 seals to cover the screws, in that order: - Two black seals on the bottom - Three black seals on the top

4-54

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.15 LCD Module

4 Replacement Procedures

4.15 FL Inverter Board Removing the FL Inverter Board Remove the FL inverter board according to the following procedures and Figure 4-34. 1. Remove one M2.5x4.5 white flat-head screw.

Figure 4-34 Removing the FL inverter board 2. Lift the LCD module, FL inverter board and disconnect the LCD/FL cable from the LCD/FL connector. 3. Disconnect the HV cable from the HV connector and remove the FL inverter board.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-55

4 Replacement Procedures

4.15 LCD Module

Installing the FL Inverter Board Install the FL inverter board according to the following procedures and Figure 4-34. 4. Connect the LCD/FL cable to LCD/FL connecter, and connect the HV cable to the HV connector. 5. Seat the LCD module, FL inverter board in the correct position. 6. Secure the FL inverter board with one M2.5x4.5 white flat-head screw.

4-56

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.16 LCD Module

4 Replacement Procedures

4.16 LCD Module NOTE: ICs are fragile. Use extreme care not to apply pressure to the ICs along the edges of the LCD module.

NOTE: Dispose of used LCD panels (fluorescent (FL) tubes) as required by local ordinances or regulations.

NOTE: The LCD/FL cable must be carefully peeled away before disconnecting it from the module.

Removing the 15.4-inch LCD module Remove the 15.4-inch LCD module according to the following procedures and Figures 4-35, 4-36. 1. Carefully tilt the LCD module toward you. 2. Remove two M2x3 white flat-head screws on each side securing the LCD bracket.

Figure 4-35 Removing the 15.4-inch LCD module and screws

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-57

4 Replacement Procedures

4.16 LCD Module

3. Remove the LCD brackets. 4. Turn the LCD upside down. Be sure to place it on a cushioned surface such as a foam pad. 5. Remove the tape and LCD/FL cable connector. Then disconnect the LCD/FL cable.

Figure 4-36 Removing the 15.4-inch LCD module

4-58

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.16 LCD Module

4 Replacement Procedures

Installing the 15.4-inch LCD Module NOTE: LCD/FL cable must be carefully peeled away before disconnecting it from the module. Install the 15.4-inch LCD module according to the following procedures and Figures 4-35, 436. 1. Turn the LCD upside down. 2. Connect the LCD/FL cable to the LCD module connector. 3. Turn the LCD right side up. 4. Place the LCD bracket in the correct position and secure it with two M2x3 white flathead screws on each side.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-59

4 Replacement Procedures

4.17 Speakers

4.17 Speakers Removing the Speakers Remove the Speakers according to the following procedures and Figure 4-37. 1. Remove one M2.5x4 black flat-head screw securing the left speaker. 2. Remove two M2.5x4 black flat-head screws securing the right speaker. 3. Remove the left and right speakers.

Figure 4-37 Removing the speakers

Installing the Speakers Install the speakers according to the following procedures and Figure 4-37. 1. Seat the left and right speaker in the correct position. 2. Route the speaker cable in the wire guide. 3. Secure the left speaker with one M2x4 black flat-head screw. 4. Secure the right speaker with two M2x4 black flat-head screws.

4-60

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.18 Switch Cover and Button Board

4 Replacement Procedures

4.18 Switch Cover and Switch Board Removing the Switch Cover and Switch Board (for Consumer Model) Remove the Switch Cover and Switch Board according to the following procedures and Figure 4-38, 4-39. 1. Remove the Mylar and EMI tape. 2. Disconnect the switch board flat cables from CN4000 on the switch board. 3. Remove two M2.5x4 black flat-head screws.

Figure 4-38 Removing the switch cover 4. Turn the top cover right side up. 5. Remove the following 7 latches on the switch cover, in that order: - Two right latches - One latch on the front and bottom sides - Three left latches 6. Remove the switch board.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-61

4 Replacement Procedures

4.18 Switch Cover and Switch Board

Figure 4-39 Removing the switch Board

Install the Switch Cover and Switch Board Install the switch board according to the following procedures and Figure 4-38, 4-39. 1. Seat the switch board in the correct position. 2. Seat the switch cover in the correct position and secure the following 7 latches, in that order: - Two right latches - One latch on the front and bottom sides - Three left latches 3. Turn the top cover upside down. 4. Secure the switch board with two M2.5x4 black flat-head screws. 5. Connect the switch board flat cables to CN4000 on the switch board. 6. Secure the EMI tape and Mylar in the correct position.

4-62

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.18 Switch Cover and Button Board

4 Replacement Procedures

Removing the Switch Board (for Commercial Model) Remove the Switch Board according to the following procedures and Figure 4-40. 1. Remove the Mylar and EMI tape. 2. Disconnect the switch board flat cables from CN4000 on the switch board. 3. Remove two M2.5x4 black flat-head screws.

Figure 4-40 Removing the switch cover 4. Turn the top cover right side up. 5. Remove the following 7 latches on the switch cover, in that order: - Two right latches - One latch on the front and bottom sides - Three left latches 6. Remove the switch board.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-63

4 Replacement Procedures

4.18 Switch Cover and Switch Board

Install the Switch Board Install the switch board according to the following procedures and Figure 4-40. 1. Seat the switch board in the correct position. 2. Seat the switch cover in the correct position and secure the following 7 latches, in that order: - Two right latches - One latch on the front and bottom sides - Three left latches 3. Turn the top cover upside down. 4. Secure the switch board with two M2.5x4 black flat-head screws. 5. Connect the switch board flat cables to CN4000 on the switch board. 6. Secure the EMI tape and Mylar in the correct position.

4-64

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.19 Touch Pad and Button Board

4 Replacement Procedures

4.19 Touch Pad and Button Board Removing the Touch Pad and Button Board (for Consumer Model) Remove the touch pad and button board according to the following procedures and Figure 441. 1. Disconnect the touch pad flat cables from JP1 on the touch pad. 2. Remove five M2.5x4 black flat-head screws securing the touch pad. 3. Remove the touch pad.

Figure 4-41 Removing the touch pad and button board 4. Remove two M2.5x3 flat-round-head screws securing the button board. 5. Remove the button board. 6. Disconnect the button board flat cable from CN2000 on the button board.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-65

4 Replacement Procedures

4.19 Touch Pad and Button Board

Installing the Touch Pad and Button Board Install the touch pad and button board according to the following procedures and Figure 4-41. 1. Connect the button board flat cable to CN2000 on the button board. 2. Seat the button board in the correct position and secure it with two M2.5x3 flatround-head screws. 3. Seat the touch pad in the correct position and secure it with five M2.5x4 black flathead screws. 4. Connect the touch pad flat cables to JP1 on the touch pad.

4-66

Satellite A100/A105 / TECRA A7 Maintenance Manual

4.19 Touch Pad and Button Board

4 Replacement Procedures

Removing the Touch Pad and Button Board (for Commercial Model) Remove the touch pad and button board according to the following procedures and Figure 442. 1. Disconnect the touch pad flat cables from JP1 on the touch pad. 2. Remove five M2.5x4 black flat-head screws securing the touch pad. 3. Remove the touch pad.

Figure 4-42 Removing the touch pad and button board 4. Remove two M2.5x3 flat-round-head screws securing the button board. 5. Remove the button board. 6. Disconnect the button board flat cable from CN2000 on the button board.

Satellite A100/A105 / TECRA A7 Maintenance Manual

4-67

4 Replacement Procedures

4.19 Touch Pad and Button Board

Installing the Touch Pad and Button Board Install the touch pad and button board according to the following procedures and Figure 4-42. 1. Connect the button board flat cable to CN2000 on the button board. 2. Seat the button board in the correct position and secure it with two M2.5x3 flatround-head screws. 3. Seat the touch pad in the correct position and secure it with five M2.5x4 black flathead screws. 4. Connect the touch pad flat cables to JP1 on the touch pad.

4-68

Satellite A100/A105 / TECRA A7 Maintenance Manual

6000 1 次

Appendices

Appendices

App-ii

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

Appendix

Contents

Appendix A Handling the LCD Module .......................................................................... A-1 Appendix B Board Layout ................................................................................................ B-1 B.1

System Board Front View ..................................................................................... B-1

B.2

System Board Back View...................................................................................... B-3

Appendix C .......................................................................................................................... C-3 Appendix C .................................................................................Error! Bookmark not defined. C.1

CN1

RJ45 Cable Connector (12-Pin)................................................................. C-3

C.2

CN2

USB Port0/Port1 Connector (8-Pin) .......................................................... C-3

C.3

CN3

LCD/FL Inverter Connector (40-Pin)........................................................ C-3

C.4

CN4

CRT Connector (15-Pin)............................................................................ C-4

C.5

CN5

Internal Left Speaker Connector (4-Pin) ................................................... C-4

C.6

CN6

Battery Connector (7-Pin )......................................................................... C-5

C.7

CN7

Parallel/B Connector(20-Pin) .................................................................... C-5

C.8

CN8

Internal Right Speaker Connector (2-Pin) ................................................. C-5

C.9

CN9

Blue Tooth Connector(20-Pin) .................................................................. C-6

C.10

CN10

VGA CARD Connector (242-Pin)........................................................... C-6

C.11

CN11

Internal Keyboard Connector (34-Pin) ................................................... C-10

C.12

CN12

Touch Pad Connector (12-Pin) ............................................................... C-10

C.13

CN13

FAN Connector (3-Pin) .......................................................................... C-11

C.14

CN14

LED Connector (16-Pin)......................................................................... C-11

C.15

CN15

Touch Pad Board Connector (6-Pin) ...................................................... C-11

C.16

CN16

Mini PCI GND Connector (1-Pin).......................................................... C-11

C.17

CN18

Stick Point Connector (8-Pin)................................................................. C-12

C.18

CN19

Mini PCI Connector (52-Pin) ................................................................. C-12

C.19

CN20

ODD Connector (50-Pin)........................................................................ C-13

C.20

CN21

S-VIDEO Connector (4-Pin) .................................................................. C-14

Satellite A100/A105 / TECRA A7 Maintenance Manual

App-iii

Appendices

C.21

CN22

IEEE 1394 Connector (4-Pin)..................................................................C-14

C.22

CN23

FingerPrint/B Connector (8-Pin) .............................................................C-14

C.23

CN24

HDD Connector (22-Pin).........................................................................C-14

C.24

CN25

CARD READER Socket (44-Pin) ...........................................................C-15

C.25

CN26

USB Port#2/#3 Connector (20-Pin).........................................................C-16

C.26

CN27

PCMCIA/NEW Card Socket (150-Pin)...................................................C-16

C.27

CN501

RJ11 Cable Connector (2-Pin)................................................................C-18

C.28

CN502

Docking Connector (240-Pin) ................................................................C-19

C.29

CN503

Power Cable Connector (4-Pin)..............................................................C-22

C.30

CN504

LAN Cable to Docking Connector (9-Pin).............................................C-22

C.31

CN506

MODEM Connector (12-Pin) .................................................................C-23

C.32

CN507

DDR2 DIMM0 Socket (200-Pin) ...........................................................C-23

C.33

CN508

DDR2 DIMM1 Socket (200-Pin) ...........................................................C-26

C.34

CN2000 Touch PAD FFC Connector (6-Pin) ......................................................C-29

C.35

CN3000 USB Board Connector (20-Pin).............................................................C-29

C.36

CN3001

USB Port 3 Connector (4-Pin)...............................................................C-30

C.37

CN3002

USB Port 2 Connector (4-Pin)...............................................................C-30

C.38

CN4000

LED Board Connector (16-Pin).............................................................C-30

C.39

CN5000

Parallel Board Connector (20-Pin) ........................................................C-30

C.40

CN5001

Parallel Port Connector (25-Pin) ...........................................................C-31

C.41

CN5002

Touch Pad Board Connector (6-Pin) .....................................................C-31

C.42

JACK 1

MICRO Phone Connector (6-Pin)..........................................................C-32

C.43

JACK 2

Head Phone Connector (6-Pin) ..............................................................C-32

C.44

FINGER1 Finger Print Connector (3-Pin) ............................................................C-32

App-iv

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

Appendix D Keyboard Scan/Character Codes................................................................ D-1 Appendix E Key Layout .................................................................................................... E-1 Appendix F BIOS Rewrite Procedures .............................................................................F-1 Appendix G EC/KBC Rewrite Procedures...................................................................... G-1 Appendix H GREASE INFORMATION ………………………………………………H-1

Satellite A100/A105 / TECRA A7 Maintenance Manual

App-v

Appendices

Figures Figure B-1 Board layout (front)...........................................................................................B-1 Figure B-2 Board layout (back) ...........................................................................................B-3 Figure E-1 US keyboard ......................................................................................................E-1 Figure E-2 JP keyboard........................................................................................................E-1 Figure E-3 SP keyboard .......................................................................................................E-1 Figure E-4 FR keyboard ......................................................................................................E-2 Figure E-5 CF keyboard ......................................................................................................E-2 Figure E-6 FR keyboard ......................................................................................................E-3 Figure E-7 GR keyboard......................................................................................................E-3 Figure E-8 IT keyboard........................................................................................................E-4 Figure E-9 TC keyboard ......................................................................................................E-4 Figure E-10 PT keyboard......................................................................................................E-5 Figure E-11 USE keyboard..................................................................................................E-5 Figure E-12 AR keyboard....................................................................................................E-6 Figure E-13 BE keyboard ....................................................................................................E-6 Figure E-14 RU keyboard....................................................................................................E-7 Figure E-15 SL keyboard.....................................................................................................E-7 Figure E-16 SW keyboard ...................................................................................................E-8 Figure E-17 NO keyboard....................................................................................................E-8 Figure E-18 DK keyboard....................................................................................................E-9 Figure E-19 TR keyboard ....................................................................................................E-9 Figure E-20 GK keyboard..................................................................................................E-10 Figure E-21 ES keyboard...................................................................................................E-10 Figure E-22 HE keyboard ..................................................................................................E-11 Figure E-23 CZ keyboard ..................................................................................................E-11 Figure E-24 LI keyboard....................................................................................................E-12 Figure E-25 HU keyboard..................................................................................................E-12 Figure E-26 SA keyboard ..................................................................................................E-13 Figure E-27 YU keyboard..................................................................................................E-13

App-vi

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

Tables Table B-1

System board connectors (front).................................................................. B-2

Table B-2

System board connectors (back) .................................................................. B-4

Table C-1

RJ45 Cable Connector pin assignments (12-Pin) ........................................ C-3

Table C-2

USB Port0/Port1 Connector pin assignments (8-Pin) ................................ C-3

Table C-3

LCD/Fl Inverter Connector pin assignments (40-Pin)................................ C-3

Table C-4

CRT Connector pin assignments (15-Pin) .................................................. C-4

Table C-5

Internal Left Speaker Connector pin assignments (4-Pin).......................... C-4

Table C-6

Battery Connector pin assignments (7-Pin ) ............................................... C-5

Table C-7

Parallel/B Connector pin assignments (20-Pin)......................................... C-5

Table C-8

Internal Right Speaker Connector pin assignments (2-Pin) ...................... C-5

Table C-9

Blue Tooth Connector pin assignments (20-Pin)........................................ C-6

Table C-10

VGA Card Connector pin assignments (242-Pin) ...................................... C-6

Table C-11

Internal Keyboard Connector pin assignments (34-Pin) ........................ C-10

Table C-12

Touch Pad Connector pin assignments (12-Pin) .................................... C-10

Table C-13

FAN Connector pin assignments (3-Pin)................................................. C-11

Table C-14

LED Connector pin assignments (16-Pin) .............................................. C-11

Table C-15

Touch Pad Board Connector pin assignments (6-Pin)............................. C-11

Table C-16

Mini PCI GND Connector pin assignments (1-Pin) ............................... C-11

Table C-17

Stick Point Connector pin assignments (8-Pin) ...................................... C-12

Table C-18

Mini PCi Connector pin assignments (52-Pin) ....................................... C-12

Table C-19

ODD Connector pin assignments (50-Pin) ............................................. C-13

Table C-20

S-VIDEO Connector pin assignments (4-Pin)......................................... C-14

Table C-21

IEEE 1394 Connector pin assignments (4-Pin) ....................................... C-14

Table C-22

FingerPrint/B Connector pin assignments (22-Pin)................................. C-14

Table C-23

HDD Connector pin assignments (22-Pin) .............................................. C-14

Table C-24

CARD READER Socket pin assignments (44-Pin) ................................ C-15

Table C-25

USB Port#2/#3 Connector pin assignments (20-Pin) .............................. C-16

Table C-26

PCMCIA/NEW Card Socket pin assignments (150-Pin) ........................ C-16

Table C-27

RJ11 Cable Connector pin assignments (2-Pin) ...................................... C-18

Table C-28

Docking Connector pin assignments (240-Pin) ...................................... C-19

Satellite A100/A105 / TECRA A7 Maintenance Manual

App-vii

Appendices

Table C-29

Power Cable Connector pin assignments (4-Pin) ........................................C-22

Table C-30

Lan cable to Docking Connector pin assignments (9-Pin) ........................C-22

Table C-31

MODEM Connector pin assignments (12-Pin) ..........................................C-23

Table C-32

DDR2 DIMM0 Socket pin assignments (200-Pin)......................................C-23

Table C-33

DDR2 DIMM1 Socket pin assignments (200-Pin).....................................C-26

Table C-34

Touch PAD FFC Connector pin assignments (6-Pin) .................................C-29

Table C-35

USB Board Connector pin assignments (20-Pin) ........................................C-29

Table C-36

USB Port 3 Connector pin assignments (4-Pin) .........................................C-30

Table C-37

USB Port 2 Connector pin assignments (4-Pin) ..........................................C-30

Table C-38

LED Board Connector pin assignments (16-Pin) ........................................C-30

Table C-39

Parallel Board Connector pin assignments (20-Pin)....................................C-30

Table C-40

Parallel Port Connector pin assignments (25-Pin).......................................C-31

Table C-41

Touch Pad Board Connector pin assignments (6-Pin).................................C-31

Table C-42

MICRO Phone Connector pin assignments (6-Pin).....................................C-32

Table C-43

Head Phone Connector pin assignments (6-Pin) .........................................C-32

Table C-44

Finger Print Connector pin assignments (3-Pin) .........................................C-32

Table D-1

Scan codes (set 1 and set 2) .......................................................................... D-1

Table D-2

Scan codes with left Shift key....................................................................... D-5

Table D-3

Scan codes in Numlock mode....................................................................... D-6

Table D-4

Scan codes with Fn key ................................................................................ D-6

Table D-5

Scan codes in overlay mode.......................................................................... D-7

Table D-6

No.124 key scan code ................................................................................... D-7

Table D-7

No.126 key scan code ................................................................................... D-8

App-viii

Satellite A100/A105 / TECRA A7 Maintenance Manual

Apx. A Handling the LCD Module

Appendices

Appendix A

Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module:

1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained.

2. Be careful to align the four holes at the right side and left side of the LCD module with the corresponding holes in the LCD cover before securing the module with four screws. Do not force the module into place, because stress can affect its performance. Also, the panel’s polarized surface is easily scarred, so be carefully when handling it.

Satellite A100/A105 / TECRA A7 Maintenance Manual

A-1

Appendices

Apx. A Handling the LCD Module

3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel. Also, never scratch the surface.

4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it. Be sure to quickly wipe off any liquid.

A-2

Satellite A100/A105 / TECRA A7 Maintenance Manual

Apx. A Handling the LCD Module

Appendices

5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks.

6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module.

Satellite A100/A105 / TECRA A7 Maintenance Manual

A-3

Appendices

Apx. A Handling the LCD Module

7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods.

8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.

A-4

Satellite A100/A105 / TECRA A7 Maintenance Manual

Apx. A Handling the LCD Module

Appendices

9. Do not disassemble the LCD module. Disassembly can cause malfunctions.

10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization.

Satellite A100/A105 / TECRA A7 Maintenance Manual

A-5

Apx. B Board Layout

Appendices

Appendix B

Appendix B Board Layout B.1

System Board Front View

Figure B-1 Board layout (front)

Satellite A100/A105 / TECRA A7 Maintenance Manual

B-1

Appendices

Apx. B Board Layout

Figure B-2 Board layout ( back )

B-2

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

Apx. C Pin Assignments

Appendix C C-3 C.1

CN1

RJ45 Cable Connector (12-Pin)................................................................. C-3

C.2

CN2

USB Port0/Port1 Connector (8-Pin) .......................................................... C-3

C.3

CN3

LCD/FL Inverter Connector (40-Pin)........................................................ C-3

C.4

CN4

CRT Connector (15-Pin)............................................................................ C-4

C.5

CN5

Internal Left Speaker Connector (4-Pin) ................................................... C-4

C.6

CN6

Battery Connector (7-Pin )......................................................................... C-5

C.7

CN7

Parallel/B Connector(20-Pin) .................................................................... C-5

C.8

CN8

Internal Right Speaker Connector (2-Pin) ................................................. C-5

C.9

CN9

Blue Tooth Connector(20-Pin) .................................................................. C-6

C.10

CN10

VGA CARD Connector (242-Pin)........................................................... C-6

C.11

CN11

Internal Keyboard Connector (34-Pin) ................................................... C-10

C.12

CN12

Touch Pad Connector (12-Pin) ............................................................... C-10

C.13

CN13

FAN Connector (3-Pin) .......................................................................... C-11

C.14

CN14

LED Connector (16-Pin)......................................................................... C-11

C.15

CN15

Touch Pad Board Connector (6-Pin) ...................................................... C-11

C.16

CN16

Mini PCI GND Connector (1-Pin).......................................................... C-11

C.17

CN18

Stick Point Connector (8-Pin)................................................................. C-12

C.18

CN19

Mini PCI Connector (52-Pin) ................................................................. C-12

C.19

CN20

ODD Connector (50-Pin)........................................................................ C-13

C.20

CN21

S-VIDEO Connector (4-Pin) .................................................................. C-14

C.21

CN22

IEEE 1394 Connector (4-Pin)................................................................. C-14

C.22

CN23

FingerPrint/B Connector (8-Pin) ............................................................ C-14

C.23

CN24

HDD Connector (22-Pin)........................................................................ C-14

C.24

CN25

CARD READER Socket (44-Pin) .......................................................... C-15

C.25

CN26

USB Port#2/#3 Connector (20-Pin)........................................................ C-16

C.26

CN27

PCMCIA/NEW Card Socket (150-Pin).................................................. C-16

C.27

CN501

RJ11 Cable Connector (2-Pin)............................................................... C-18

C.28

CN502

Docking Connector (240-Pin)................................................................ C-19

C.29

CN503

Power Cable Connector (4-Pin)............................................................. C-22

C.30

CN504

LAN Cable to Docking Connector (9-Pin)............................................ C-22

C.31

CN506

MODEM Connector (12-Pin) ................................................................ C-23

Satellite A100/A105 / TECRA A7 Maintenance Manual

C-1

Appendices

Apx. C Pin Assignments

C.32

CN507

DDR2 DIMM0 Socket (200-Pin) ...........................................................C-23

C.33

CN508

DDR2 DIMM1 Socket (200-Pin) ...........................................................C-26

C.34

CN2000 Touch PAD FFC Connector (6-Pin) ......................................................C-29

C.35

CN3000

USB Board Connector (20-Pin).............................................................C-29

C.36

CN3001

USB Port 3 Connector (4-Pin)...............................................................C-30

C.37

CN3002

USB Port 2 Connector (4-Pin)...............................................................C-30

C.38

CN4000

LED Board Connector (16-Pin).............................................................C-30

C.39

CN5000

Parallel Board Connector (20-Pin) ........................................................C-30

C.40

CN5001

Parallel Port Connector (25-Pin) ...........................................................C-31

C.41

CN5002

Touch Pad Board Connector (6-Pin) .....................................................C-31

C.42

JACK 1

MICRO Phone Connector (6-Pin)..........................................................C-31

C.43

JACK 2

Head Phone Connector (6-Pin) ..............................................................C-32

C.44

FINGER1 Finger Print Connector (3-Pin) ............................................................C-32

C-2

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

Apx. C Pin Assignments

Appendix C

Appendix C

Pin Assignments

System Board

C.1

CN1

Table C-1

RJ45 Cable Connector (12-Pin)

RJ45 Cable Connector pin assignments (12-Pin)

Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11

/TD+' /RD+' /LAN_45' /LAN_78' +V3_LAN' +V3_LAN

l

2 4 6 8 10 12

/TD-' /LAN_45' /RD-' /LAN_78' LED_LANACT# LED_LANLINK

I

C.2

CN2

Table C-2

O O O -

O O O I I

USB Port0/Port1 Connector (8-Pin)

USB Port0/Port1 Connector pin assignments (8-Pin)

Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7

/USBVCC1' /USB_L_P0+' /USBVCC1' /USB_L_P1+'

-

2 4 6 8

/USB_L_P0-' DGND' /USB_L_P1-' DGND'

I/O

C.3

CN3

Table C-3

I/O I/O

I/O -

LCD/FL Inverter Connector (40-Pin)

LCD/Fl Inverter Connector pin assignments (40-Pin)

Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11

DGND' DGND' DGND' /LVDS_TXDL0-' /LVDS_TXDL0+' /LVDS_TXDL2-'

-

2 4 6 8 10 12

/N$904505' /N$904505' /+V3S' /LVDS_TXDL1-' /LVDS_TXDL1+' /LVDS_TXCL-'

-

I I I

Satellite A100/A105 / TECRA A7 Maintenance Manual

I I I

C-3

Appendices

Apx. C Pin Assignments

13 15 17 19 21 23 25 27 29 31 33 35 37 39

C.4

/LVDS_TXDL2+' DGND' /LVDS_TXDU0-' /LVDS_TXDU0+' /LVDS_TXDU2-' /LVDS_TXDU2+' DGND' /LCM_DDCPCLK_3S' /N$867421' /N$867421' /N$867421' /INV_PWM_3' DGND' DGND'

CN4

I I I I I I/O I -

14 16 18 20 22 24 26 28 30 32 34 36 38 40

/LVDS_TXCL+' DGND' /LVDS_TXDU1-' /LVDS_TXDU1+' /LVDS_TXCU-' /LVDS_TXCU+' DGND' /LCM_DDCPDATA_3S' /N$867421' /N$867421' /N$867421' /N$890544' DGND' DGND'

I I I I I I/O -

CRT Connector (15-Pin)

Table C-4 CRT Connector pin assignments (15-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15

R B DGND' DGND' +V5S

I I I I/O

2 4 6 8 10 12 14

G

I I I

C.5

/CRT_HSYNC' DDC_CLK

CN5

Table C-5

C-4

DGND' DGND' DGND' DDCDAT /CRT_VSYNC'

Internal Left Speaker Connector (4-Pin)

Internal Left Speaker Connector pin assignments (4-Pin)

Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1

SPK_OUT_L+

O

2

SPK_OUT_L-

O

3

/MACHINE_ID5'

I

4

/N$820315'

I

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

C.6

Apx. C Pin Assignments

CN6

Battery Connector (7-Pin )

Table C-6 Battery Connector pin assignments (7-Pin ) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7

DGND' /BATT_DATA' /N$874497' VPACK

-

2 4 6 -

/BATT_CLK' THRM_IN /BATT_ID'

I/O-

-

-

C.7

CN7

I/O -

O O

Parallel/B Connector(20-Pin)

Table C-7 Parallel/B Connector pin assignments (20-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19

/STRB#_5R' /PDATA(1)_R' /PDATA(3)_R' /PDATA(5)_R' /PDATA(7)_R' /BUSY_5R' /SLCT_5R' /ERROR#_5R' /SLCTIN#_5R' DGND'

I

2 4 6 8 10 12 14 16 18 20

/PDATA(0)_R' /PDATA(2)_R' /PDATA(4)_R' /PDATA(6)_R' /ACK#_5R' /PE_5R' /ALF#_5R' /PINIT#_5R' DGND' DGND'

I

C.8

CN8

I/O I I I/O I I I I/O -

I I I/O I I I/O I/O -

Internal Right Speaker Connector (2-Pin)

Table C-8 Internal Right Speaker Connector pin assignments (2-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1

SPK_OUT_R+

O

2

SPK_OUT_R-

O

Satellite A100/A105 / TECRA A7 Maintenance Manual

C-5

Appendices

C.9

Apx. C Pin Assignments

CN9

Blue Tooth Connector(20-Pin)

Table C-9 Blue Tooth Connector pin assignments (20-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19

DGND' /BTMDL#' /BTWAKEUP' DGND' /N$760730' /USB_P4-' -

-

2 4 6 8 10 12 14 16 18 20

/BT_RESET#' /BT20_CLK' /USB_P4+' /BT20_DATA' /BTRF-E3V'

-

C.10

CN10

I/O I/O I I/O -

I/O I/O I/O I/O I/O

VGA CARD Connector (242-Pin)

Table C-10 VGA Card Connector pin assignments (242-Pin)

C-6

Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31

/+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' DGND' DGND' DGND' -

-

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32

/+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' /+V1.8_VRAM' -

-

-

-

-

-

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101

Apx. C Pin Assignments

/PCIE_RST#' /SLP_S3_5R' /THRM_SHUTDWN#' /SLP_S3#_5R' /+V0.9S' /+V0.9S' /+V0.9S' /EC_DATA' /EC_CLK' /VGA_ID_S' DGND' /PEG_C_RXN15' /PEG_C_RXP15' DGND' /PEG_C_RXN14' /PEG_C_RXP14' DGND' /PEG_C_RXN13' /PEG_C_RXP13' DGND' /PEG_C_RXN12' /PEG_C_RXP12' DGND' /PEG_C_RXN11' /PEG_C_RXP11' DGND' /PEG_C_RXN10' /PEG_C_RXP10' DGND' /PEG_C_RXN9' /PEG_C_RXP9'

I/O O O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O

34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102

Satellite A100/A105 / TECRA A7 Maintenance Manual

/+V3S' /+V3S' /+V1.5S_VGA' /+V1.5S_VGA' /+V1.5S_VGA' /+V1.5S_VGA' /+V1.5S_VGA' /+V5A' /+V5A' DGND' /PEG_C_TXN15' /PEG_C_TXP15' DGND' /PEG_C_TXN14' /PEG_C_TXP14' DGND' /PEG_C_TXN13' /PEG_C_TXP13' DGND' /PEG_C_TXN12' /PEG_C_TXP12' DGND' /PEG_C_TXN11' /PEG_C_TXP11' DGND' /PEG_C_TXN10' /PEG_C_TXP10' DGND' /PEG_C_TXN9' /PEG_C_TXP9'

I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O

C-7

Appendices

103 105 107 109 111 113 115 117 119 121 123 125 127 129 131 133 135 137 139 141 143 145 147 149 151 153 155 157 159 161 163 165 167 169 171

C-8

Apx. C Pin Assignments

DGND' /PEG_C_RXN8' /PEG_C_RXP8' DGND' /PEG_C_RXN7' /PEG_C_RXP7' DGND' /PEG_C_RXN6' /PEG_C_RXP6' DGND' /PEG_C_RXN5' /PEG_C_RXP5' DGND' /PEG_C_RXN4' /PEG_C_RXP4' DGND' /PEG_C_RXN3' /PEG_C_RXP3' DGND' /PEG_C_RXN2' /PEG_C_RXP2' DGND' /PEG_C_RXN1' /PEG_C_RXP1' DGND' /PEG_C_RXN0' /PEG_C_RXP0' DGND' DGND' DGND' -

I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O -

104 106 108 110 112 114 116 118 120 122 124 126 128 130 132 134 136 138 140 142 144 146 148 150 152 154 156 158 160 162 164 166 168 170 172

DGND' /PEG_C_TXN8' /PEG_C_TXP8' DGND' /PEG_C_TXN7' /PEG_C_TXP7' DGND' /PEG_C_TXN6' /PEG_C_TXP6' DGND' /PEG_C_TXN5' /PEG_C_TXP5' DGND' /PEG_C_TXN4' /PEG_C_TXP4' DGND' /PEG_C_TXN3' /PEG_C_TXP3' DGND' /PEG_C_TXN2' /PEG_C_TXP2' DGND' /PEG_C_TXN1' /PEG_C_TXP1' DGND' /PEG_C_TXN0' /PEG_C_TXP0' DGND' /CLK_R_PEG_REF' /CLK_R_PEG_REF#' DGND' /LVDS_TXCU+' /LVDS_TXCU-' DGND' /LVDS_TXDU2+'

I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

173 175 177 179 181 183 185 187 189 191 193 195 197 199 201 203 205 207 209 211 213 215 217 219 221 223 225 227 229 231 233 235 237 239 241

Apx. C Pin Assignments

DGND' DGND' DGND' DGND' DGND' /CRT_VSYNC' /CRT_HSYNC' /CRT_DDCCLK' /CRT_DDCDATA' /LCM_3S_VDDEN' /LCM_3S_BKLTEN' /INV_PWM_3' /LCM_DDCPCLK_3S' /LCM_DDCPDATA_3S' /+V2.5S' /+V2.5S' /+V2.5S' /+VBAT' /+VBAT' /+VBAT' /+VBAT'

I/O I/O I/O I/O I/O I/O I/O I/O I/O -

174 176 178 180 182 184 186 188 190 192 194 196 198 200 202 204 206 208 210 212 214 216 218 220 222 224 226 228 230 232 234 236 238 240 242

Satellite A100/A105 / TECRA A7 Maintenance Manual

/LVDS_TXDU2-' DGND' /LVDS_TXDU0+' /LVDS_TXDU0-' DGND' /LVDS_TXDU1+' /LVDS_TXDU1-' DGND' /LVDS_TXDL1+' /LVDS_TXDL1-' DGND' /LVDS_TXDL0+' /LVDS_TXDL0-' DGND' /LVDS_TXDL2+' /LVDS_TXDL2-' DGND' /LVDS_TXCL+' /LVDS_TXCL-' DGND' /CRT_R' DGND' /CRT_G' DGND' /CRT_B' DGND' /SVID_LUMA' DGND' /SVID_CHROMA' DGND' /+VBAT' /+VBAT' /+VBAT' /+VBAT'

I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O -

C-9

Appendices

C.11

Apx. C Pin Assignments

CN11

Internal Keyboard Connector (34-Pin)

Table C-11 Internal Keyboard Connector pin assignments (34-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33

/+V5S'

I -

/+V5S' /SCAN_OUT(2)' /SCAN_IN(1)' /SCAN_OUT(0)' /SCAN_IN(3)' /SCAN_OUT(6)' /SCAN_IN(6)' /SCAN_OUT(12)' /SCAN_OUT(3)' /SCAN_OUT(13)' /SCAN_OUT(8)' /SCAN_OUT(10)' /SCAN_OUT(15)' /N$466922' /N$466924'

-

/SCAN_OUT(4)' /SCAN_IN(2)' /SCAN_OUT(1)' /SCAN_IN(0)' /SCAN_OUT(5)' /SCAN_IN(5)' /SCAN_IN(4)' /SCAN_OUT(7)' /SCAN_IN(7)' /SCAN_OUT(9)' /SCAN_OUT(11)' /SCAN_OUT(14)' /+V5S' /N$466923'

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34

C.12

CN12

O I O I O I I O I O O O -

I O I O I O I O O O O O O -

Touch Pad Connector (12-Pin)

Table C-12 Touch Pad Connector pin assignments (12-Pin)

C-10

Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11

/IM_CLK_5' /IM_DAT_5' /TPL_SW' /TPR_SW' DGND' +V5S'

I/O

2 4 6 8 10 12

/PS2_R_SW' /PS2_L_SW' /PS2_DAT_5' /PS2_CLK_5' DGND' +V5S

O

I/O

I I -

O

I/O I/O -

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

C.13

Apx. C Pin Assignments

CN13

FAN Connector (3-Pin)

Table C-13 FAN Connector pin assignments (3-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1

VCC

I

2

DGND

-

3

FAN_TACH1'

O

C.14

CN14

LED Connector (16-Pin)

Table C-14 LED Connector pin assignments (16-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15

/PWR_OLED#_VCC' /PWR_OLED#' /PWR_BUF_BLED#_VCC' /SCAN_IN(0)' /SCAN_IN(3)' /SCAN_IN(5)' /MACHINE_ID0_DB' DGND'

O

2 4 6 8 10 12 14 16

/PWR_SWIN#_3' /PWR_BUF_BLED#' /SCAN_OUT(1)' /SCAN_IN(2)' /SCAN_IN(4)' /SCAN_IN(6)' /MACHINE_ID1_DB' DGND'

I

C.15

CN15

O O O O O O -

O O O O O O -

Touch Pad Board Connector (6-Pin)

Table C-15 Touch Pad Board Connector pin assignments (6-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5

/TPL_SW' /TPR_SW' DGND'

I/O

2 4 6

/TPL_SW' /TPR_SW' DGND'

I/O

C.16

CN16

I/O -

I/O -

Mini PCI GND Connector (1-Pin)

Table C-16 Mini PCI GND Connector pin assignments (1-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1

DGND'

-

-

-

-

Satellite A100/A105 / TECRA A7 Maintenance Manual

C-11

Appendices

C.17

Apx. C Pin Assignments

CN18

Stick Point Connector (8-Pin)

Table C-17 Stick Point Connector pin assignments (8-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7

/PS2_R_SW' /PS2_L_SW' /PS2_DAT_5' DGND'

I/O

2 4 6 8

/PS2_CLK_5' DGND' /N$783140'

-

C.18

CN19

I/O I/O -

I/O -

Mini PCI Connector (52-Pin)

Table C-18 Mini PCi Connector pin assignments (52-Pin)

C-12

Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43

/PCIE_WAKE#' /CH_DATA' /CH_CLK' /CLK_REQB#' DGND' /CLK_R_PCIE_MINI1#' /CLK_R_PCIE_MINI1' DGND' /BUF_PLT_RST#' /CLK_R3S_MINICARDPCI' DGND' /PCIE_C_RXN3' /PCIE_C_RXP3' DGND' DGND' /PCIE_C_TXN3' /PCIE_C_TXP3' DGND' -

I/O-

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44

/+V3S' DGND' /+V1.5S' /LPC_3S_FRAME#' /LPC_3S_AD(3)' /LPC_3S_AD(2)' /LPC_3S_AD(1)' /LPC_3S_AD(0)' DGND' /N$744283' /BUF_PLT_RST#' /N$744273' DGND' /+V1.5S' /ICH_3A_ALERT_CLK' /ICH_3A_ALERT_DAT' DGND' DGND' -

-

I/O O I/O I/O I/O I/O I/O I/OI/O I/O I/O -

I/O I/O I/O I/O I/O I/O I/O I/O -

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

Apx. C Pin Assignments

45 47 49 51

C.19

-

CN20

46 48 50 52

-

/+V1.5S' DGND' /+V3S'

-

ODD Connector (50-Pin)

Table C-19 ODD Connector pin assignments (50-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49

/A_CD_L' /A_CD_GND' /N$591279' /SDD(7)' /SDD(6)' /SDD(5)' /SDD(4)' /SDD(3)' /SDD(2)' /SDD(1)' /SDD(0)' DGND' /SDIOW#_3' /SDIORDY_35' /IRQ15_3' /SDA(1)' /SDA(0)' /SDCS1#_3' /MBDASP#_5' /+V5S' /+V5S' DGND' DGND' /N$878073' DGND'

I/O-

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50

/A_CD_R'

I/O

/SDD(8)' /SDD(9)' /SDD(10)' /SDD(11)' /SDD(12)' /SDD(13)' /SDD(14)' /SDD(15)' /SDDRQ_35' /SDIOR#_3' DGND' /SDDACK#_35'

-

I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O -

Satellite A100/A105 / TECRA A7 Maintenance Manual

/SDA(2)' /SDCS3#_3' /+V5S' /+V5S' /+V5S' DGND' DGND' DGND' DGND'

I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O -

C-13

Appendices

C.20

Apx. C Pin Assignments

CN21

S-VIDEO Connector (4-Pin)

Table C-20 S-VIDEO Connector pin assignments (4-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1

DGND' /SVID_L_LUMA'

-

2

-

I/O

4

DGND' /SVID_L_CHROMA'

3

C.21

CN22

I/O

IEEE 1394 Connector (4-Pin)

Table C-21 IEEE 1394 Connector pin assignments (4-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3

/1394_L_TPB0N' /1394_L_TPA0N'

I/O-

2 4

/1394_L_TPB0P' /1394_L_TPA0P'

I/O

C.22

CN23

I/O

I/O-

FingerPrint/B Connector (8-Pin)

Table C-22 FingerPrint/B Connector pin assignments (22-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7

/+V3S' DGND' /USB_P5-'

I/O

2 4 6 8

/+V3S' /USB_P5+' DGND'

I/O -

C.23

CN24

HDD Connector (22-Pin)

Table C-23 HDD Connector pin assignments (22-Pin)

C-14

Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13

DGND' /SATA_C_TX0-' /SATA_C_RX0-' DGND'

I/O I/O -

2 4 6 8 10 12 14

/SATA_C_TX0+' DGND' /SATA_C_RX0+'

I/O I/O -

+V3S DGND' DGND'

+V3S +V3S DGND' /+V5S'

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

Apx. C Pin Assignments

15 17 19 21

C.24

/+V5S' DGND' DGND' -

CN25

-

16 18 20 22

/+V5S' -

-

CARD READER Socket (44-Pin)

Table C-24 CARD READER Socket pin assignments (44-Pin) Pin No.

Signal Name

I/O

Pin No.

1

DGND'

-

2

3 /MS_DATA1_SD_DAT1_SM_D1' I/O 4 5 /MS_DATA2_SD_DAT2_SM_D2' I/O 6

Signal Name

I/O

I/O /MS_DATA0_SD_DAT0_SM_D0' I/O

/MS_BS_SD_CMD_SM_WEZ' /MS_CDZ'

I/O

7 /MS_DATA3_SD_DAT3_SM_D3' I/O 8 /MS_CLK_SD_CLK_SM_ELWPZ' I/O /VCC_MC' DGND' - 10 9 11 /MS_DATA2_SD_DAT2_SM_D2' I/O 12 /MS_DATA3_SD_DAT3_SM_D3' I/O DGND' 13 /MS_BS_SD_CMD_SM_WEZ' I/O 14 15

/VCC_MC'

-

16 /MS_CLK_SD_CLK_SM_ELWPZ' I/O

17

DGND'

-

18

-

-

19 /MS_DATA0_SD_DAT0_SM_D0' I/O 20 /MS_DATA1_SD_DAT1_SM_D1' I/O /SD_CDZ' DGND' I/O 22 21 23

/XD_CDZ'

I/O 24

DGND'

-

25

/SM_RBZ'

I/O 26

/SM_REZ'

I/O

27

/SD_WP_SM_CEZ'

I/O 28

/SM_CLE'

I/O

29

/SM_ALE'

I/O 30

/MS_BS_SD_CMD_SM_WEZ'

31

/N$780179'

I/O -

-

32

DGND'

33 /MS_DATA0_SD_DAT0_SM_D0' I/O 34 /MS_DATA1_SD_DAT1_SM_D1' I/O 35 /MS_DATA2_SD_DAT2_SM_D2' I/O 36 /MS_DATA3_SD_DAT3_SM_D3' I/O 37

/SM_D4'

I/O 38

/SM_D5'

I/O

39

/SM_D6'

I/O 40

/SM_D7'

I/O

41

/VCC_MC'

-

-

43

/SD_WP_SM_CEZ'

DGND'

-

-

42

I/O 44

Satellite A100/A105 / TECRA A7 Maintenance Manual

C-15

Appendices

C.25

Apx. C Pin Assignments

CN26

USB Port#2/#3 Connector (20-Pin)

Table C-25 USB Port#2/#3 Connector pin assignments (20-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19

/USB_VCC2' /USB_VCC2' /USB_VCC2' /LID_VCC' /BT_WLON#' /BT_WLON#_VCC' /KILL_SWCH#' /USB_P2-' DGND' /USB_P3+'

-

2 4 6 8 10 12 14 16 18 20

/USB_VCC2' /USB_VCC2' /USB_VCC2' /KILL_VCC' /LID_SW#_3' DGND' DGND' /USB_P2+' /USB_P3-' DGND'

-

C.26

CN27

I/O I/O I/O I/O I/O

I/O I/O I/O -

PCMCIA/NEW Card Socket (150-Pin)

Table C-26 PCMCIA/NEW Card Socket pin assignments (150-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31

DGND' DGND' DGND' DGND' DGND' /PCIE_C_TXP2' DGND' /PCIE_RXP2' DGND' DGND'

-

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32

DGND' DGND' DGND' DGND' /PCIE_C_TXN2' DGND' /PCIE_RXN2' DGND' DGND'

-

C-16

-I/O I/O -

I/O I/O -

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101

DGND' /CLK_R_PCIE_CARD#' DGND' DGND' DGND' DGND' /+V3_EXP' /+V3_EXP' /+V3_EXP' DGND' /+V3AUX_EXP' /PCIE_WAKE#' /+V1.5_EXP' DGND' /N$811981' DGND' DGND' DGND' /USB_P6-' DGND' DGND' /ACARD_3S_CLKRUN#' /ACARD_3S_D(2)_RFU' /ACARD_3S_AD29' /ACARD_3S_AD28' /ACARD_3S_STSCHG' /ACARD_3S_AUDIO' /ACARD_3S_CBE3#' /ACARD_3S_AD24' /ACARD_3S_AD23' /ACARD_3S_AD22' /ACARD_3S_AD21' /ACARD_3S_VS2#'

Apx. C Pin Assignments

O I/O I/O I/O I/O I/O I/O I/O I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O

34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102

Satellite A100/A105 / TECRA A7 Maintenance Manual

/CLK_R_PCIE_CARD' DGND' DGND' DGND' /CPPE#' /+V3_EXP' /+V3_EXP' /PERST#' /+V3AUX_EXP' /+V3AUX_EXP' /+V1.5_EXP' /+V1.5_EXP' /N$811982' DGND' DGND' DGND' /CPUSB#' /USB_P6+' DGND' DGND' /ACARD_3S_CD2#' /ACARD_3S_AD31' /ACARD_3S_AD30' DGND' /ACARD_3S_AD27' /ACARD_3S_AD26' /ACARD_3S_AD25' DGND' /ACARD_3S_REQ#' /ACARD_3S_SERR#' /ACARD_3S_RST#' DGND' /ACARD_3S_AD20'

O I/O I/O I/O I/O I/O I/O I/O I/O I/O I I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O

C-17

Appendices

103 105 107 109 111 113 115 117 119 121 123 125 127 129 131 133 135 137 139 141 143 145 147 149

Apx. C Pin Assignments

I/O

/ACARD_3S_AD19' /ACARD_3S_AD17' /ACARD_3S_FRAME#' /ACARD_3S_IRDY#' /N$842787' /ACARD_3S_INT#' /ACARD_3S_GNT#' /ACARD_3S_STOP#' /ACARD_3S_BLOCK#' /ACARD_3S_A18_RFU' /ACARD_3S_AD16' /ACARD_3S_AD14' /ACARD_3S_AD12' /ACARD_3S_AD11' /ACARD_3S_AD9' /ACARD_3S_AD10' /ACARD_3S_AD8' /ACARD_3S_D(14)_RFU' /ACARD_3S_AD6' /ACARD_3S_AD3' /ACARD_3S_AD1' /ACARD_3S_AD0' DGND'

C.27

CN501

I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O -

104 106 108 110 112 114 116 118 120 122 124 126 128 130 132 134 136 138 140 142 144 146 148 150

/ACARD_3S_AD18' /ACARD_3S_CBE2#' DGND' /ACARD_3S_TRDY#' /ACARDVPP' /ACARDVCC' /ACARD_3S_DEVSEL#' DGND' /ACARD_3S_PERR#' /ACARD_3S_PAR' /ACARD_3S_CBE1#' DGND' /ACARD_3S_AD15' /ACARD_3S_AD13' /ACARD_3S_VS1#' DGND' /ACARD_3S_CBE0#' /ACARD_3S_AD7' /ACARD_3S_AD5' DGND' /ACARD_3S_AD4' /ACARD_3S_AD2' /ACARD_3S_CD1#' DGND'

I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O -

RJ11 Cable Connector (2-Pin)

Table C-27 RJ11 Cable Connector pin assignments (2-Pin)

C-18

Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1

/MDMTIP_DOCK'

-

2

/MDMRNG_DOCK'

-

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

C.28

Apx. C Pin Assignments

CN502

Docking Connector (240-Pin)

Table C-28 Docking Connector pin assignments (240-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61

/DCOUT' /DOCDT1#' /MOUSCK' DGND' /N$633280' DGND' /D_ROUT' /D_BOUT' /DVISC' DGND' /DVITX2-' /DVITX1-' /DVITX0-' DGND' /DVITXC-' DGND' DGND' DGND' DGND' /D+_DOCK' /MDMRNG_DOCK' /DCOUT'

I/O

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62

/DCOUT' /IF_P5V' /EXKBCK' /PHYRST#' DGND' /CRT_DDCCLK' /D_GOUT' /DVSYNC' /DVITX2+' /DVITX1+' /DVITX0+' DGND' /DVITXC+' /DVIDET#' /D-_DOCK' /MDMTIP_DOCK' /DCOUT'

I/O

I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O

Satellite A100/A105 / TECRA A7 Maintenance Manual

I/O I/O I/O O I/O I/O I/O I/O O I/O I/O I/O I/O O

C-19

Appendices

63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101 103 105 107 109 111 113 115 117 119 121 123 125 127 129 131

C-20

Apx. C Pin Assignments

/EJECTRQ#' /MOUSDT' DGND' /N$750503' DGND' DGND' DGND' /DVISD' DGND' /DVITX5-' /DVITX4-' /DVITX3-' DGND' DGND' DGND' DGND' DGND' /C-_DOCK' /C+_DOCK' /DCOUT' /DOCK_I2C_CLK' /N$634193' DGND' DGND'

I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O -

64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102 104 106 108 110 112 114 116 118 120 122 124 126 128 130 132

/IF_P5V' /EXKBDT' /CRT_DDCDATA' DGND' /DHSYNC' /DVITX5+' /DVITX4+' /DVITX3+' DGND' /DCOUT' /IF_P5V' /1394_TPA1P' /1394_TPB1P' -

I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O -

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

133 135 137 139 141 143 145 147 149 151 153 155 157 159 161 163 165 167 169 171 173 175 177 179 181 183 185 187 189 191 193 195 197 199 201

Apx. C Pin Assignments

/DINL+' DGND' /DDCD#_3' /DTXD_3' /PE_5' /PDATA(6)' DGND' /PDATA(1)' /PDATA(0)' DGND' DGND' DGND' DGND' DGND' /+V3_LAN' /TD+_DOCK' /DCOUT' /DOCK_I2C_DATA' DGND' /USB_P7+' DGND' /DOUTR-' /DINL-' DGND' /DRTS_3'

I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O I/O O

134 136 138 140 142 144 146 148 150 152 154 156 158 160 162 164 166 168 170 172 174 176 178 180 182 184 186 188 190 192 194 196 198 200 202

Satellite A100/A105 / TECRA A7 Maintenance Manual

/N$752559' /DOUTL+' /DINR-' /PWR_SWIN#_3' /DDSR#_3' /DRI#_3' /PDATA(7)' DGND' /PDATA(4)' /PDATA(2)' /STRB#_5' /TD-_DOCK' /DCOUT' /IF_P5V' /1394_TPA1N' /1394_TPB1N' /USB_P7-' /DOUTR+' /DOUTL-' /DINR+' /DRXD_3' /DCTS_3'

O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O

C-21

Appendices

203 205 207 209 211 213 215 217 219 221 223 225 227 229 231 233 235 237 239

Apx. C Pin Assignments

/DDTR#_3' /BUSY_5' /PDATA(5)' DGND' /SLCTIN#_5' /ERROR#_5' DGND' DGND' DGND' DGND' DGND' /LED_R3S_LANLINK#' /RD+_DOCK'

C.29

CN503

I/O I/O I/O O I/O O I/O

204 206 208 210 212 214 216 218 220 222 224 226 228 230 232 234 236 238 240

/SLCT_5' /ACK#_5' DGND' /PDATA(3)' /PINIT#_5' /ALF#_5' /LED_R3S_LANACT#' /DOCDT2#' /RD-_DOCK'

I/O I/O I O I/O I/O O I/O

Power Cable Connector (4-Pin)

Table C-29 Power Cable Connector pin assignments (4-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1

+VADPTR'

-

2

+VADPTR

-

3

DGND

-

4

DGND

-

C.30

CN504

LAN Cable to Docking Connector (9-Pin)

Table C-30 Lan cable to Docking Connector pin assignments (9-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5

/TD+_DOCK' /RD+_DOCK' DGND'

I/O

2 4 6

/TD-_DOCK' /RD-_DOCK' /C+_DOCK'

I/O

C-22

I/O

-

I/O I/O

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

7 9

C.31

Apx. C Pin Assignments

/C-_DOCK' /D-_DOCK'

CN506

8 -

I/O I/O

/D+_DOCK' -

I/O

-

MODEM Connector (12-Pin)

Table C-31 MODEM Connector pin assignments (12-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11

DGND' /MC97_3S_SDOUT' DGND' /MC97_3S_SYNC' /N$791775' /MC97_3S_RST#'

I/O I/O I/O

2 4 6 8 10 12

/MDC' DGND' DGND' /MC97_3S_BITCLK'

I/O I/O

C.32

CN507

DDR2 DIMM0 Socket (200-Pin)

Table C-32 DDR2 DIMM0 Socket pin assignments (200-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31

/SM_VREF' DGND' /M_DATA(0)' /M_DATA(1)' DGND' /M_DQS#(0)' /M_DQS(0)' DGND' /M_DATA(2)' /M_DATA(3)' DGND' /M_DATA(8)' /M_DATA(9)' DGND' /M_DQS#(1)' /M_DQS(1)'

O

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32

DGND' /M_DATA(4)' /M_DATA(5)' DGND' /M_DM(0)' DGND' /M_DATA(6)' /M_DATA(7)' DGND' /M_DATA(12)' /M_DATA(13)' DGND' /M_DM(1)' DGND' /M_CLK_DDR4' /M_CLK_DDR4#'

-

33

DGND'

34

DGND'

I/O I/O O I/O I/O I/O I/O O I/O I/O -

Satellite A100/A105 / TECRA A7 Maintenance Manual

I/O I O I/O I/O I/O I/O O I/O I/O -

C-23

Appendices

35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101 103

C-24

Apx. C Pin Assignments

/M_DATA(10)' /M_DATA(11)' DGND' DGND' /M_DATA(16)' /M_DATA(17)' DGND' /M_DQS#(2)' /M_DQS(2)' DGND' /M_DATA(18)' /M_DATA(19)' DGND' /M_DATA(24)' /M_DATA(25)' DGND' /M_DM(3)' DGND' /M_DATA(26)' /M_DATA(27)' DGND' /M_CKE2' /+V1.8' /M_A(17)' /+V1.8' /M_A(12)' /M_A(9)' /M_A(8)' /+V1.8' /M_A(5)' /M_A(3)' /M_A(1)' /+V1.8'

O O I/O I/O I/O I/O I/O I/O I/O O O I/O I/O I/O I I/O I/O I/O I/O O I/O I/O I/O -

36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102 104

/M_DATA(14)' /M_DATA(15)' DGND' DGND' /M_DATA(20)' /M_DATA(21)' DGND' /M_DM(2)' DGND' /M_DATA(22)' /M_DATA(23)' DGND' /M_DATA(28)' /M_DATA(29)' DGND' /M_DQS#(3)' /M_DQS(3)' DGND' /M_DATA(30)' /M_DATA(31)' DGND' /M_CKE3' /+V1.8' /M_A(14)' /+V1.8' /M_A(11)' /M_A(7)' /M_A(6)' /+V1.8' /M_A(4)' /M_A(2)' /M_A(0)' /+V1.8'

O O I/O I/O I/O I/O I/O O O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I/O I/O I/O -

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

105 107 109 111 113 115 117 119 121 123 125 127 129 131 133 135 137 139 141 143 145 147 149 151 153 155 157 159 161 163 165 167 169 171 173

Apx. C Pin Assignments

/M_A(10)' /M_A(15)' /M_WE#' /+V1.8' /M_CAS#' /M_CS3#' /+V1.8' /M_ODT3' DGND' /M_DATA(32)' /M_DATA(33)' DGND' /M_DQS#(4)' /M_DQS(4)' DGND' /M_DATA(34)' /M_DATA(35)' DGND' /M_DATA(40)' /M_DATA(41)' DGND' /M_DM(5)' DGND' /M_DATA(42)' /M_DATA(43)' DGND' /M_DATA(48)' /M_DATA(49)' DGND' DGND' /M_DQS#(6)' /M_DQS(6)' DGND' /M_DATA(50)'

I/O I/O I/O I/O I/O O O I/O I/O I/O I/O O I/O I/O I/O I/O O I/O I/O I/O O I/O

106 108 110 112 114 116 118 120 122 124 126 128 130 132 134 136 138 140 142 144 146 148 150 152 154 156 158 160 162 164 166 168 170 172 174

Satellite A100/A105 / TECRA A7 Maintenance Manual

/M_A(16)' /M_RAS#' /M_CS2#' /+V1.8' /M_ODT1' /M_A(13)' /+V1.8' DGND' /M_DATA(36)' /M_DATA(37)' DGND' /M_DM(4)' DGND' /M_DATA(38)' /M_DATA(39)' DGND' /M_DATA(44)' /M_DATA(45)' DGND' /M_DQS#(5)' /M_DQS(5)' DGND' /M_DATA(46)' /M_DATA(47)' DGND' /M_DATA(52)' /M_DATA(53)' DGND' /M_CLK_DDR3' /M_CLK_DDR3#' DGND' /M_DM(6)' DGND' /M_DATA(54)'

I/O I/O I/O I/O O I/O I/O I/O O I/O I/O I/O I/O O I/O I/O O O I/O I/O O I/O

C-25

Appendices

175 177 179 181 183 185 187 189 191 193 195 197 199

C.33

Apx. C Pin Assignments

/M_DATA(51)' DGND' /M_DATA(56)' /M_DATA(57)' DGND' /M_DM(7)' DGND' /M_DATA(58)' /M_DATA(59)' DGND' /SB_SMDAT_3' /SB_SMCLK_3' /+V3S'

CN508

I/O I/O I/O

I/O I/O I/O I/O -

176 178 180 182 184 186 188 190 192 194 196 198 200

/M_DATA(55)' DGND' /M_DATA(60)' /M_DATA(61)' DGND' /M_DQS#(7)' /M_DQS(7)' DGND' /M_DATA(62)' /M_DATA(63)' DGND' /N$837418' /N$837419'

I/O I/O I/O

O I/O

I/O I/O I/O -

DDR2 DIMM1 Socket (200-Pin)

Table C-33 DDR2 DIMM1 Socket pin assignments (200-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31

/SM_VREF' DGND' /M_DATA(0)' /M_DATA(1)' DGND' /M_DQS#(0)' /M_DQS(0)' DGND' /M_DATA(2)' /M_DATA(3)' DGND' /M_DATA(8)' /M_DATA(9)' DGND' /M_DQS#(1)' /M_DQS(1)'

I/O -

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32

DGND' /M_DATA(4)' /M_DATA(5)' DGND' /M_DM(0)' DGND' /M_DATA(6)' /M_DATA(7)' DGND' /M_DATA(12)' /M_DATA(13)' DGND' /M_DM(1)' DGND' /M_CLK_DDR1' /M_CLK_DDR1#'

-

33

DGND'

34

DGND'

C-26

I/O I/O O I/O I/O I/O I/O O I/O I/O -

I I/OI/O I/O I/O I/O O I/O I/O -

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101 103

Apx. C Pin Assignments

/M_DATA(10)' /M_DATA(11)' DGND' DGND' /M_DATA(16)' /M_DATA(17)' DGND' /M_DQS#(2)' /M_DQS(2)' DGND' /M_DATA(18)' /M_DATA(19)' DGND' /M_DATA(24)' /M_DATA(25)' DGND' /M_DM(3)' DGND' /M_DATA(26)' /M_DATA(27)' DGND' /M_CKE0' /+V1.8' /M_A(17)' /+V1.8' /M_A(12)' /M_A(9)' /M_A(8)' /+V1.8' /M_A(5)' /M_A(3)' /M_A(1)' /+V1.8'

O O I/O I/O I/O I/O I/O I/O O I I/O O I/O -

I/O I/O I/O O I/O I/O I/O -

36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102 104

Satellite A100/A105 / TECRA A7 Maintenance Manual

/M_DATA(14)' /M_DATA(15)' DGND' DGND' /M_DATA(20)' /M_DATA(21)' DGND' /M_DM(2)' DGND' /M_DATA(22)' /M_DATA(23)' DGND' /M_DATA(28)' /M_DATA(29)' DGND' /M_DQS#(3)' /M_DQS(3)' DGND' /M_DATA(30)' /M_DATA(31)' DGND' /M_CKE1' /+V1.8' /M_A(14)' /+V1.8' /M_A(11)' /M_A(7)' /M_A(6)' /+V1.8' /M_A(4)' /M_A(2)' /M_A(0)' /+V1.8'

I I I/O O O I/O I/O I/O I/O O I/O I/O -

I O O O O I/O I/O I/O -

C-27

Appendices

105 107 109 111 113 115 117 119 121 123 125 127 129 131 133 135 137 139 141 143 145 147 149 151 153 155 157 159 161 163 165 167 169 171 173

C-28

Apx. C Pin Assignments

/M_A(10)' /M_A(15)' /M_WE#' /+V1.8' /M_CAS#' /M_CS1#' /+V1.8' /M_ODT2' DGND' /M_DATA(32)' /M_DATA(33)' DGND' /M_DQS#(4)' /M_DQS(4)' DGND' /M_DATA(34)' /M_DATA(35)' DGND' /M_DATA(40)' /M_DATA(41)' DGND' /M_DM(5)' DGND' /M_DATA(42)' /M_DATA(43)' DGND' /M_DATA(48)' /M_DATA(49)' DGND' DGND' /M_DQS#(6)' /M_DQS(6)' DGND' /M_DATA(50)'

I/O I/O I/O I/O I/O O O I/O I/O O I/O I/O I/O O I/O

O I/O O I/O O I/O

106 108 110 112 114 116 118 120 122 124 126 128 130 132 134 136 138 140 142 144 146 148 150 152 154 156 158 160 162 164 166 168 170 172 174

/M_A(16)' /M_RAS#' /M_CS0#' /+V1.8' /M_ODT0' /M_A(13)' /+V1.8' DGND' /M_DATA(36)' /M_DATA(37)' DGND' /M_DM(4)' DGND' /M_DATA(38)' /M_DATA(39)' DGND' /M_DATA(44)' /M_DATA(45)' DGND' /M_DQS#(5)' /M_DQS(5)' DGND' /M_DATA(46)' /M_DATA(47)' DGND' /M_DATA(52)' /M_DATA(53)' DGND' /M_CLK_DDR0' /M_CLK_DDR0#' DGND' /M_DM(6)' DGND' /M_DATA(54)'

I/O I/O I/O I/O O O O I/O I/O O I/O I/O I/O I/O O I/O I/O

I/O I/O O I/O I/O I/O

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

175 177 179 181 183 185 187 189 191 193 195 197 199

C.34

Apx. C Pin Assignments

O I/O I/O I/O -

/M_DATA(51)' DGND' /M_DATA(56)' /M_DATA(57)' DGND' /M_DM(7)' DGND' /M_DATA(58)' /M_DATA(59)' DGND' /SB_SMDAT_3' /SB_SMCLK_3' /+V3S'

CN2000

I/O I/O I/O I/O -

176 178 180 182 184 186 188 190 192 194 196 198 200

/M_DATA(55)' DGND' /M_DATA(60)' /M_DATA(61)' DGND' /M_DQS#(7)' /M_DQS(7)' DGND' /M_DATA(62)' /M_DATA(63)' DGND' DGND' /N$842459'

I/O I/O I/O I/O I/O I/O I/O -

Touch PAD FFC Connector (6-Pin)

Table C-34 Touch PAD FFC Connector pin assignments (6-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5

GROUND_TP' /RIGHT_TP' /LEFT_TP'

-

2 4 6

GROUND_TP' /RIGHT_TP' /LEFT_TP'

-

C.35

CN3000

O O

O O

USB Board Connector (20-Pin)

Table C-35 USB Board Connector pin assignments (20-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17

/USBVCC2' /USBVCC2' /USBVCC2' /LID_VCC_DB' /BT_WLON#_DB' /BT_WLON#_VCC_DB' /KILL_SWCH#_DB' /USB_P2-_DB' USB_GND'

-

2 4 6 8 10 12 14 16 18

/USBVCC2' /USBVCC2' /USBVCC2' /KILL_VCC_DB' /LID_SW#_3_DB' USB_GND' USB_GND' /USB_P2+_DB' /USB_P3-_DB'

-

19

/USB_P3+_DB'

20

USB_GND'

I I I I I/O I/O

Satellite A100/A105 / TECRA A7 Maintenance Manual

I O I/O I/O -

C-29

Appendices

C.36

Apx. C Pin Assignments

CN3001

USB Port 3 Connector (4-Pin)

Table C-36 USB Port 3 Connector pin assignments (4-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3

/USBVCC2' /USB_L_P3+'

-

2 4

/USB_L_P3-' USB_GND'

I/O

C.37

CN3002

I/O

-

USB Port 2 Connector (4-Pin)

Table C-37 USB Port 2 Connector pin assignments (4-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3

/USBVCC2' /USB_L_P2+'

-

2 4

/USB_L_P2-' USB_GND'

I/O

C.38

CN4000

I/O

-

LED Board Connector (16-Pin)

Table C-38 LED Board Connector pin assignments (16-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15

GROUND_DBSW' /MACHINE_ID1_DBSW' /N$816074' /N$816062' /N$816050' /N$577940' /PWR_BLED#_DBSW' /PWR_SWIN#_3_DBSW'

O

2 4 6 8 10 12 14 16

GROUND_DBSW' /MACHINE_ID0_DBSW' /N$816068' /N$816056' /N$816044' /PWR_BLED#_VCC_DBSW' /PWR_OLED#_DBSW' /PWR_OLED#_VCC_DBSW'

O

C.39

CN5000

O O I

O O O O

Parallel Board Connector (20-Pin)

Table C-39 Parallel Board Connector pin assignments (20-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5

PRINT_GND' PRINT_GND' /PINIT#_5_DB'

-

2 4 6

PRINT_GND' /SLCTIN#_5_DB' /ERROR#_5_DB'

-

C-30

I/O

I/O I/O

Satellite A100/A105 / TECRA A7 Maintenance Manual

Appendices

7 9 11 13 15 17 19

C.40

Apx. C Pin Assignments

/ALF#_5_DB' /PE_5_DB' /ACK#_5_DB' /PDATA_DB(6)' /PDATA_DB(4)' /PDATA_DB(2)' /PDATA_DB(0)'

CN5001

I I I I I/O I/O I/O

8 10 12 14 16 18 20

/SLCT_5_DB' /BUSY_5_DB' /PDATA_DB(7)' /PDATA_DB(5)' /PDATA_DB(3)' /PDATA_DB(1)' /STRB#_5_DB'

I O I/O I/O I/O I/O I/O

Parallel Port Connector (25-Pin)

Table C-40 Parallel Port Connector pin assignments (25-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5 7 9 11 13 15 17 19 21 23 25

/STRB#_5_DB' /PDATA_DB(1)' /PDATA_DB(3)' /PDATA_DB(5)' /PDATA_DB(7)' /BUSY_5_DB' /SLCT_5_DB' /ERROR#_5_DB' /SLCTIN#_5_DB' PRINT_GND' PRINT_GND' PRINT_GND' PRINT_GND'

I/O

2 4 6 8 10 12 14 16 18 20 22 24 -

/PDATA_DB(0)' /PDATA_DB(2)' /PDATA_DB(4)' /PDATA_DB(6)' /ACK#_5_DB' /PE_5_DB' /ALF#_5_DB' /PINIT#_5_DB' PRINT_GND' PRINT_GND' PRINT_GND' PRINT_GND' -

I/O

C.41

CN5002

I/O I/O I/O I/O I/O I/O I/O I/O -

I/O I/O I/O I/O I/O I/O I/O -

Touch Pad Board Connector (6-Pin)

Table C-41 Touch Pad Board Connector pin assignments (6-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5

GROUND_PK' /RIGHT_PK' /LEFT_PK'

I/O

2 4 6

GROUND_PK' /RIGHT_PK' /LEFT_PK'

-

C.42

JACK 1

I/O I/O

I/O I/O

MICRO Phone Connector (6-Pin)

Table C-42 MICRO Phone Connector pin assignments (6-Pin)

Satellite A100/A105 / TECRA A7 Maintenance Manual

C-31

Appendices

Apx. C Pin Assignments

Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1

ANAGND

-

2

MIC

I

3

AREF

I/O

4

ANAGND

-

5

ANAGND

-

6

AREF

I/O

C.43

JACK 2

Head Phone Connector (6-Pin)

Table C-43 Head Phone Connector pin assignments (6-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3 5

ANAGND' HP_R ANAGND'

I

2 4 6

HP_L ANAGND HPS

O

C.44

O I

I I

FINGER1 Finger Print Connector (3-Pin)

Table C-44 Finger Print Connector pin assignments (3-Pin) Pin No.

Signal Name

I/O

Pin No.

Signal Name

I/O

1 3

/LEFT_UD' GROUND_UD'

I

2

/RIGHT_UD'

I

-

-

-

-

C-32

Satellite A100/A105 / TECRA A7 Maintenance Manual

Keyboard Scan/Character Codes Apx. D

Appendices

Keyboard Scan/Character Codes

Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Cap

Code set 1

Note

Code set 2

No.

Keytop

Make

Break

Make

01

‘ ~

29

A9

0E

F0

0E

02

1 !

02

82

16

F0

16

03

2 @

03

83

1E

F0

1E

04

3 #

04

84

26

F0

26

05

4 $

05

85

25

F0

25

06

5 %

06

86

2E

F0

2E

07

6 ^

07

87

36

F0

36

08

7 &

08

88

3D

F0

3D

*2

09

8 *

09

89

3E

F0

3E

*2

10

9 (

0A

8A

46

F0

46

*2

11

0 )

0B

8B

45

F0

45

*2

12

- _

0C

8C

4E

F0

4E

13

= +

0D

8D

55

F0

55

7D

F0

7D

14

Break

15

BkSp

0E

8E

66

F0

66

16

Tab

0F

8F

0D

F0

0D

17

Q

10

90

15

F0

15

18

W

11

91

1D

F0

1D

19

E

12

92

24

F0

24

20

R

13

93

2D

F0

2D

21

T

14

94

2C

F0

2C

22

Y

15

95

35

F0

35

23

U

16

96

3C

F0

3C

*2

24

I

17

97

43

F0

43

*2

25

O

18

98

44

F0

44

*2

26

P

19

99

4D

F0

4D

*2

27

[ {

1A

9A

54

F0

54

28

] }

1B

9B

5B

F0

5B

Satellite A100/A105 / TECRA A7 Maintenance Manual

D-1

Appendices

Keyboard Scan/Character Codes

Table D-1 Scan codes (set 1 and set 2) (2/4) Cap

D-2

Code set 1

Code set 2

Note

No.

Keytop

Make

Break

Make

29

\ |

2B

AB

5D

F0

5D

30

Caps Lock

3A

BA

58

F0

58

31

A

1E

9E

1C

F0

1C

32

S

1F

9F

1B

F0

1B

33

D

20

A0

23

F0

23

34

F

21

A1

2B

F0

2B

35

G

22

A2

34

F0

34

36

H

23

A3

33

F0

33

37

J

24

A4

3B

F0

3B

*2

38

K

25

A5

42

F0

42

*2

39

L

26

A6

4B

F0

4B

*2

40

; :

27

A7

4C

F0

4C

*2

41

‘ “

28

A8

52

F0

52

43

Enter

1C

9C

5A

F0

5A

44

Shift (L)

2A

AA

12

F0

12

45

No.102 key

56

D6

61

F0

61

46

Z

2C

AC

1A

F0

1A

47

X

2D

AD

22

F0

22

48

C

2E

AE

21

F0

21

49

V

2F

AF

2A

F0

2A

50

B

30

B0

32

F0

32

51

N

31

B1

31

F0

31

52

M

32

B2

3A

F0

3A

*2

53

, <

33

B3

41

F0

41

*2

54

. >

34

B4

49

F0

49

*2

55

/ ?

35

B5

4A

F0

4A

*2

56

\_

73

F0

73

57

Shift (R)

59

F0

59

36

B6

Break *5

*3

Satellite A100/A105 / TECRA A7 Maintenance Manual

Keyboard Scan/Character Codes

Appendices

Table D-1 Scan codes (set 1 and set 2) (3/4) Cap

Code set 1

Code set 2

Note

No.

Keytop

Make

Break

Make

58

Ctrl

1D

9D

14

F0

14

*3

60

Alt (L)

38

B8

11

F0

11

*3

61

Space

39

B9

29

F0

29

62

ALT (R)

E0

38

E0

B8

E0

11

E0

F0

11

75

Ins

E0

52

E0

D2

E0

70

E0

F0

70

*1

76

Del

E0

53

E0

D3

E0

71

E0

F0

71

*1

79

E0

4B

E0

CB

E0

6B

E0

F0

6B

*1

80

Home

E0

47

E0

C7

E0

6C

E0

F0

6C

*1

81

End

E0

4F

E0

CF

E0

69

E0

F0

69

*1

83

E0

48

E0

C8

E0

75

E0

F0

75

*1

84

E0

50

E0

D0

E0

72

E0

F0

72

*1

85

PgUp

E0

49

E0

C9

E0

7D

E0

F0

7D

*1

86

PgDn

E0

51

E0

D1

E0

7A

E0

F0

7A

*1

89

E0

4D

E0

CD

E0

74

E0

F0

74

*1

110

Esc

01

81

76

F0

76

112

F1

3B

BB

05

F0

05

113

F2

3C

BC

06

F0

06

114

F3

3D

BD

04

F0

04

115

F4

3E

BE

0C

F0

0C

116

F5

3F

BF

03

F0

03

117

F6

40

C0

0B

F0

0B

118

F7

41

C1

83

F0

83

119

F8

42

C2

0A

F0

0A

120

F9

43

C3

01

F0

01

121

F10

44

C4

09

F0

09

Satellite A100/A105 / TECRA A7 Maintenance Manual

Break

*3

D-3

Appendices

Keyboard Scan/Character Codes

Table D-1 Scan codes (set 1 and set 2) (4/4) Cap

Code set 1 Make

Code set 2

Break

Make

Note

No.

Keytop

Break

122

F11

57

D7

78

F0

78

*3

123

F12

58

D8

7

F0

7

*3

124

PrintSc *6

*6

*6

*6

*6

126

Pause

*7

*7

*7

*7

*7

202

Fn

*4

203

Win

E0

5B

E0

DB

E0

1F

E0

F0

1F

204

App

E0

5D

E0

DD

E0

2F

E0

F0

2F

205

Kat/Hir

70

F0

70

*8

206

Hen

79

F0

79

*8

207

Muh

7B

F0

7B

*8

Notes: 1. 2. 3. 4. 5. 6. 7. 8.

D-4

* * * * * * * *

Scan codes differ by mode. Scan codes differ by overlay function. Combination with the Fn key makes different codes. Fn key does not generate a code by itself. This key corresponds to key No. 42 in a 102-key model. Refer to Table D-6, No. 124 key scan code. Refer to Table D-7, No. 126 key scan code. 205~207 are for JAPAN keyboard only

Satellite A100/A105 / TECRA A7 Maintenance Manual

Keyboard Scan/Character Codes

Appendices

Table D-2 Scan codes with left Shift key Cap

Key

Code set 1

Code set 2

No.

top

55

/

E0

AA

E0

35

E0

B5

E0

2A

E0

F0

12

E0

4A

E0

F0

4A

E0

12

75

INS

E0

AA

E0

52

E0

D2

E0

2A

E0

F0

12

E0

70

E0

F0

70

E0

12

76

DEL

E0

AA

E0

53

E0

D3

E0

2A

E0

F0

12

E0

71

E0

F0

71

E0

12

79

E0

AA

E0

4B

E0

CB

E0

2A

E0

F0

12

E0

6B

E0

F0

6B

E0

12

80

Home

E0

AA

E0

47

E0

C7

E0

2A

E0

F0

12

E0

6C

E0

F0

6C

E0

12

81

End

E0

AA

E0

4F

E0

CF

E0

2A

E0

F0

12

E0

69

E0

F0

69

E0

12

83

E0

AA

E0

48

E0

C8

E0

2A

E0

F0

12

E0

75

E0

F0

75

E0

12

84

E0

AA

E0

50

E0

D0

E0

2A

E0

F0

12

E0

72

E0

F0

72

E0

12

85

PgUp

E0

AA

E0

49

E0

C9

E0

2A

E0

F0

12

E0

7D

E0

F0

7D

E0

12

86

PgDn

E0

AA

E0

51

E0

D1

E0

2A

E0

F0

12

E0

7A

E0

F0

7A

E0

12

89

E0

AA

E0

4D

E0

CD

E0

2A

E0

F0

12

E0

74

E0

F0

74

E0

12

203

Win

E0

AA

E0

5B

E0

DB

E0

2A

E0

F0

12

E0

1F

E0

F0

1F

E0

12

204

App

E0

AA

E0

5D

E0

DD

E0

2A

E0

F0

12

E0

2F

E0

F0

2F

E0

12

Make

Break

Make

Break

Note : The table above shows scan codes with the left Shift key. In combination with the right Shift key, scan codes are changed as listed below: Set 1 Set 2

With left Shift E0 AA __________ E0 2A ___________ E0 F0 12 ________ E0 12 ___________

With right Shift E0 B6 E0 36 E0 F0 59 E0 59

Satellite A100/A105 / TECRA A7 Maintenance Manual

D-5

Appendices

Keyboard Scan/Character Codes

Table D-3 Scan codes in Numlock mode Cap

Key

Code set 1

No.

top

75

INS

E0

2A

E0

52

E0

D2

E0

AA

E0

12

E0

70

E0

F0

70

E0

F0

12

76

DEL

E0

2A

E0

53

E0

D3

E0

AA

E0

12

E0

71

E0

F0

71

E0

F0

12

79

E0

2A

E0

4B

E0

CB

E0

AA

E0

12

E0

6B

E0

F0

6B

E0

F0

12

80

Home

E0

2A

E0

47

E0

C7

E0

AA

E0

12

E0

6C

E0

F0

6C

E0

F0

12

81

End

E0

2A

E0

4F

E0

CF

E0

AA

E0

12

E0

69

E0

F0

69

E0

F0

12

83

E0

2A

E0

48

E0

C8

E0

AA

E0

12

E0

75

E0

F0

75

E0

F0

12

84

E0

2A

E0

50

E0

D0

E0

AA

E0

12

E0

72

E0

F0

72

E0

F0

12

85

PgUp

E0

2A

E0

49

E0

C9

E0

AA

E0

12

E0

7D

E0

F0

7D

E0

F0

12

86

PgDn

E0

2A

E0

51

E0

D1

E0

AA

E0

12

E0

7A

E0

F0

7A

E0

F0

12

89

E0

2A

E0

4D

E0

CD

E0

AA

E0

12

E0

74

E0

F0

74

E0

F0

12

203

Win

E0

2A

E0

5B

E0

DB

E0

AA

E0

12

E0

1F

E0

F0

1F

E0

F0

12

204

App

E0

2A

E0

5D

E0

DD

E0

AA

E0

12

E0

2F

E0

F0

2F

E0

F0

12

Make

Code set 2 Break

Make

Break

Table D-4 Scan codes with Fn key Cap

Code set 1

Code set 2

No.

Keytop

43

ENT

E0

1C

E0

9C

E0

5A

E0

F0

5A

58

CTRL

E0

1D

E0

9D

E0

14

E0

F0

14

60

LALT

E0

38

E0

B8

E0

11

E0

F0

11

121

ARROW

45

C5

77

F0

77

122

NUMERIC

45

C5

77

F0

77

123

Scrl

46

C5

7E

F0

7E

D-6

Make

Break

Make

Break

Satellite A100/A105 / TECRA A7 Maintenance Manual

Keyboard Scan/Character Codes

Appendices

Table D-5 Scan codes in overlay mode Cap No.

Keytop

Code set 1

Code set 2

Make

Break

Make

Break

08

7

(7)

47

C7

6C

F0

6C

09

8

(8)

48

C8

75

F0

75

10

9

(9)

49

C9

7D

F0

7D

11

(*)

37

B7

7C

F0

7C

23

U

(4)

4B

CB

6B

F0

6B

24

I

(5)

4C

CC

73

F0

73

25

O

(6)

4D

CD

74

F0

74

26

P

(–)

4A

CA

7B

F0

7B

37

J

(1)

4F

CF

69

F0

69

38

K

(2)

50

D0

72

F0

72

39

L

(3)

51

D1

7A

F0

7A

40

;

(+)

4E

CE

79

F0

79

52

M

(0)

52

D2

70

F0

70

54

.

(.)

53

D3

71

F0

71

55

/

(/)

E0

35

E0

B5

40

4A

E0

F0

4A

Table D-6 No.124 key scan code Key top

Shift

Prt Sc

Common

Code set 1 Make 2A

E0

Ctrl +

E0

Shift +

E0

Alt +

E0

Code set 2 Break

37

E0

B7

E0

37

E0

37

E0

54

D4

Make 12

E0

B7

E0

B7

E0

Satellite A100/A105 / TECRA A7 Maintenance Manual

AA

E0

Break 7C

E0

F0

7C

E0

7C

E0

F0

7C

7C

E0

F0

7C

84

F0

B4

F0

12

D-7

Appendices

Keyboard Scan/Character Codes

Table D-7 No.126 key scan code Key top Pause

Shift

Code set 1

Code set 2

Make

Make

Common* E1 1D

45

E1

Ctrl*

E0

C6

E0 46

9D

C5

E1

14

77

E1

F0

E0

7E

E0

F0

7E

14

F0

*: This key generates only make codes.

D-8

Satellite A100/A105 / TECRA A7 Maintenance Manual

77

Apx. E Key Layout Apx. E

Appendices

Key Layout

Appendix E E.1

Key Layout

United States (US) Keyboard

Figure E-1 US keyboard

E.2

Japan (JP) Keyboard

Figure E-2 JP keyboard

Satellite A100/A105 / TECRA A7 Maintenance Manual

E-1

Appendices

E.3

Apx E Key Layout

Spanish (SP) Keyboard

Figure E-3 SP keyboard

E.4

Korean (KR) Keyboard

Figure E-4 KR keyboard

E-2

Satellite A100/A105 / TECRA A7 Maintenance Manual

Apx.E Key Layout

E.5

Appendices

Canadian-French (CF) Keyboard

Figure E-5 CF keyboard

E.6

French (FR) Keyboard

Figure E-6 FR keyboard

Satellite A100/A105 / TECRA A7 Maintenance Manual

E-3

Appendices

E.7

Apx E Key Layout

German (GR) Keyboard

Figure E-7 GR keyboard

E.8

Italian (IT) Keyboard

Figure E-8 IT keyboard

E-4

Satellite A100/A105 / TECRA A7 Maintenance Manual

Apx E Key Layout

E.9

Appendices

Taiwan (TC) Keyboard

Figure E-9 TC keyboard

E.10 Portuguese (PT) Keyboard

Figure E-11 PT keyboard

Satellite A100/A105 / TECRA A7 Maintenance Manual

E-5

Appendices

Apx E Key Layout

E.11 DU, UE, US International (USE) Keyboard

Figure E-12 USE keyboard

E.12 Arabic (AR) Keyboard

Figure E-13 AR keyboard

E-6

Satellite A100/A105 / TECRA A7 Maintenance Manual

Apx E Key Layout

Appendices

E.13 Belgian (BE) Keyboard

Figure E-14 BE keyboard

E.14 Russian (RU) Keyboard

Figure E-15 RU keyboard

Satellite A100/A105 / TECRA A7 Maintenance Manual

E-7

Appendices

Apx E Key Layout

E.15 Swiss/Switzerland (SL) Keyboard

Figure E-16 SL keyboard

E.16 Swedish (SW) Keyboard

Figure E-17 SW keyboard

E-8

Satellite A100/A105 / TECRA A7 Maintenance Manual

Apx E Key Layout

Appendices

E.17 Norwegian (NO) Keyboard

Figure E-18 NO keyboard

E.18 Danish (DK) Keyboard

Figure E-19 DK keyboard

Satellite A100/A105 / TECRA A7 Maintenance Manual

E-9

Appendices

Apx E Key Layout

E.19 Turkey (TR) Keyboard

Figure E-18 TR keyboard

E.20 Greek (GK) Keyboard

Figure E-19 GK keyboard

E-10

Satellite A100/A105 / TECRA A7 Maintenance Manual

Apx E Key Layout

Appendices

E.21 Estonia (ES) Keyboard

Figure E-19 ES keyboard

E.22 Herbrew (HE) Keyboard

Figure E-19 HE keyboard

Satellite A100/A105 / TECRA A7 Maintenance Manual

E-11

Appendices

Apx E Key Layout

E.23 Czech (CZ) Keyboard

Figure E-18 CZ keyboard

E.24 Lithuanian (LI) Keyboard

Figure E-18 LI keyboard

E-12

Satellite A100/A105 / TECRA A7 Maintenance Manual

Apx E Key Layout

Appendices

E.25 Hungary (HU) Keyboard

Figure E-18 HU keyboard

E.26 Slovakia (SA) Keyboard

Figure E-18 SA keyboard

Satellite A100/A105 / TECRA A7 Maintenance Manual

E-13

Appendices

Apx E Key Layout

E.27 Yugoslavia (YU) Keyboard

Figure E-19 YU keyboard

E-14

Satellite A100/A105 / TECRA A7 Maintenance Manual

Apx. F BIOS Rewrite Procedures

Appendices

Appendix G

Appendix F

BIOS Rewrite Procedures

This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool: ‰ BIOS/EC/KBC rewriting disk for the computer that has renewed BIOS data. Rewriting the BIOS 1. Set the system to boot mode. 2. Turn off the power to the computer. 3. Remove the external cable and PC card. 4. Connect an external FDD and insert the BIOS/EC/KBC rewriting disk into either the external FDD. 5. Turn on the power while holding down the [`~] key (on the left of the space key). (Keep holding down the key until a message appears on the screen.) The BIOS rewriting starts. 6. When the process is completed, eject the BIOS/EC/KBC rewriting disk and the system is automatically reset.

Satellite A100/A105 / TECRA A7 Maintenance Manual

F-1

Apx. G EC/KBC Rewrite Procedures

Appendices

Appendix H

Appendix G EC/KBC Rewrite Procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system.

Tools To rewrite the EC/KBC, you need the following tool: ‰ BIOS/EC/KBC rewriting disk for the computer

Rewriting the EC/KBC 1. Set the system to boot mode. 2. Turn off the power to the computer. 3. Remove the external cable and PC Card. 4. Connect an external FDD and insert the BIOS/EC/KBC rewriting disk into either the external FDD. 5. Turn on the power while holding down the [`~] key. (Keep holding down the key until a message appears on the screen.) The EC/KBC rewriting starts. 6. When the EC/KBC rewrite is completed, the system is automatically turned off. Note:

1. Rewrite the EC/KBS only when instructed by a diagnostic disk release1 notice. 2. Connect the AC adapter to the computer when you rewrite the EC/KBC. 3. Do not turn off the power while you are rewriting the EC/KBC. If the rewrite fails, it might be impossible to start up the computer. 4. If you fail to rewrite EC/KBC, then when you next turn on the power, a message may be displayed that the contents of the EC/KBC have been erased. In this case, insert the BIOS/EC/KBC rewriting disk, and the EC/KBC will be rewritten. 5. Normally it takes about 30 seconds to rewrite the EC/KBC. It may take 3 minutes (maximum), depending on the conditions of the computer or ICs. The computer is not hung up. Allow sufficient time. Never reboot or turn off the power to the computer before the rewriting is completed.

Satellite A100/A105 / TECRA A7 Maintenance Manual

G-1

Apx. H GREASE INFORMATION

Appendices

Appendix H

Appendix H GREASE INFORMATION This Appendix explains which grease use this model.

Satellite A100/A105 / TECRA A7 Maintenance Manual

H-1

[PDF] Toshiba Personal Computer Satellite A100/A105 TECRA A7 (PSAA8/PSAA9) (PTA70/PTA71) (PSAAx) Maintenance Manual - Free Download PDF (2024)

References

Top Articles
Latest Posts
Article information

Author: Kareem Mueller DO

Last Updated:

Views: 6320

Rating: 4.6 / 5 (66 voted)

Reviews: 89% of readers found this page helpful

Author information

Name: Kareem Mueller DO

Birthday: 1997-01-04

Address: Apt. 156 12935 Runolfsdottir Mission, Greenfort, MN 74384-6749

Phone: +16704982844747

Job: Corporate Administration Planner

Hobby: Mountain biking, Jewelry making, Stone skipping, Lacemaking, Knife making, Scrapbooking, Letterboxing

Introduction: My name is Kareem Mueller DO, I am a vivacious, super, thoughtful, excited, handsome, beautiful, combative person who loves writing and wants to share my knowledge and understanding with you.