Roasted potatoes recipe | Jamie Oliver recipes (2024)

FAQs

Roasted potatoes recipe | Jamie Oliver recipes? ›

Peel the potatoes, keeping them whole, and ideally all about the same size (8cm). Parboil them in a pan of boiling salted water for 15 minutes – this will ensure that the insides become really fluffy. 2. Drain in a colander and leave to steam dry for 2 minutes – this will help the fat to stick to the potatoes.

Peel the potatoes, keeping them whole, and ideally all about the same size (8cm). Parboil them in a pan of boiling salted water for 15 minutes – this will ensure that the insides become really fluffy. 2. Drain in a colander and leave to steam dry for 2 minutes – this will help the fat to stick to the potatoes.

Soaking potatoes in water helps remove excess starch. Excess starch can inhibit the potatoes from cooking evenly as well as creating a gummy or sticky texture on the outside of your potatoes. Cold water is used because hot water would react with the starch activating it, making it harder to separate from the potatoes.

In a video online, Gordon explained: “For crispy roast potatoes, you can depend on them, my tip is to parboil them, leave them to steam dry, then sprinkle them with semolina or flour, and then give them a good roughing up.”

Neutral, low-cost oil such as vegetable oil, canola oil, safflower oil, peanut oil, corn oil, coconut oil, avocado oil, etc., work well for roasting. These oils have a high smoke point, allowing the potatoes to get very hot to achieve maximum crispiness.

Preheat the fat. While the potatoes parboil, add the oil or butter to the roasting pan, transfer it to the warm oven, and heat it for about 5 minutes before adding the potatoes. This allows the outside of the potatoes to crisp up nicely and not just absorb the cold fat when you put them in the oven.

Do I have to boil potatoes before roasting? Not necessary but this can help get the perfect consistency and crispiness. Make sure you boil them but leave them a bit al dente and they will crisp up perfectly in the oven.

A: First let's talk about why cut potatoes need to be immersed in water to begin with. The reason is to prevent the potatoes exposure to air, which causes dehydration, oxidation, and discoloration. Immersing cut potatoes will also help rinse off excess starch.

Covering in water helps the potato from turning a dark color. Adding salt to the water to form a brine mixture may seem helpful and can impart a flavor to the potato strips, however, salt is a major contributor to the fry oil breaking down prematurely, so I don't recommend it.

Use parchment paper– non stick foil, or baking sheets will not do the trick. Parchment paper allows the potatoes to roast without sticking!

Why are my roast potatoes tough? ›

Go for larger chunks of potato so that the sides are bigger. This means more potato will be in contact with your pan or tray, giving it more direct heat to crunch up. The perfect roast potato has a balance of fluff in the middle and crispy exterior. Cut them too small and they're crunchy, but too hard.

Roasted potatoes can become soggy if the water content in the potato isn't fully cooked. Different potatoes have different water content percentages. Also, be mindful of the oil. Potatoes can react like sponges; too much oil can make your potatoes appear to be soggy.

Melt the lard in a deep flameproof roasting tray on a high heat and fry the potatoes on each side until they begin to brown. Sprinkle with salt and roast for 30 minutes, or until starting to colour. Turn the potatoes and return to the oven for a further 20-30 minutes, or until golden-brown and crisp.

Once the internal temp is 185°F or more (210°F is ideal) pull the potatoes from the oven, and with one hand using a mitt, place each hot potato in foil and wrap. Ideally store in a heated bread warmer drawer.

Some people suggest that you leave your boiled spuds to dry overnight before you roast. This is because the best crunch is the result of the driest potato hitting the hot fat.